It didn't start accepting them, R5 simply started giving the correct identity after the clear.
This is common. Sent from my (old) iPhone5 > On Mar 16, 2014, at 3:54, Bastien Migette <[email protected]> wrote: > > Hi Folks, > > I was playing with DMVPN lab from WB1 (Section 7 - DMVPN Phase 1) and got > this strange behaviour. > > Basically after configuring everything fine, R6 Tunnel was up, but R5 kept > being down. > > Debug IPSEC on R8 was giving: > > *Mar 16 10:34:18.200: IPSEC(validate_proposal_request): proposal part #1 > *Mar 16 10:34:18.200: IPSEC(validate_proposal_request): proposal part #1, > (key eng. msg.) INBOUND local= 192.168.8.8:0, remote= 8.9.50.5:0, > local_proxy= 8.9.2.8/255.255.255.255/47/0, > remote_proxy= 8.9.50.5/255.255.255.255/47/0, > protocol= ESP, transform= NONE (Transport-UDP), > lifedur= 0s and 0kb, > spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x0 > *Mar 16 10:34:18.200: map_db_find_best did not find match > *Mar 16 10:34:18.200: IPSEC(ipsec_process_proposal): proxy identities not > supported > > R6 was having exact same config except tunnel ip address of course. > > Then I did a clear crypto session on R5, and it suddenly started to work: > *Mar 16 10:34:51.776: IPSEC(key_engine): got a queue event with 1 KMI > message(s) > *Mar 16 10:34:51.800: IPSEC(validate_proposal_request): proposal part #1 > *Mar 16 10:34:51.800: IPSEC(validate_proposal_request): proposal part #1, > (key eng. msg.) INBOUND local= 192.168.8.8:0, remote= 8.9.50.5:0, > local_proxy= 8.9.2.8/255.255.255.255/47/0, > remote_proxy= 8.9.50.5/255.255.255.255/47/0, > protocol= ESP, transform= NONE (Transport-UDP), > lifedur= 0s and 0kb, > spi= 0x0(0), conn_id= 0, > R8(config)#keysize= 0, flags= 0x0 > *Mar 16 10:34:51.800: insert of map into mapdb AVL failed, map + ace pair > already exists on the mapdb > *Mar 16 10:34:51.800: Crypto mapdb : proxy_match > src addr : 192.168.8.8 > dst addr : 8.9.50.5 > protocol : 47 > src port : 0 > dst port : 0 > > > I am a bit curious though on why clearing crypto session on R5 would have > made R8 accepting proxy IDs. > > This is on > R8(config)#do sh ver | i IO > Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(4)M5, > RELEASE SOFTWARE (fc2) > R8(config)# > > > > I removed the EZVPN Config from previous task as well, not sure that would > made a difference. > _______________________________________________ > Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: > > iPexpert on YouTube: www.youtube.com/ipexpertinc
_______________________________________________ Free CCIE R&S, Collaboration, Data Center, Wireless & Security Videos :: iPexpert on YouTube: www.youtube.com/ipexpertinc
