Thks Kevin and Jacobs, I have not tried it yet, but I believe must work w/ your workaround,cause I remember it worked before w/ the same amount of DSP, and Kevin's explanation really make sense why it failed
--- On Sun, 11/16/08, Kevin Porter <[EMAIL PROTECTED]> wrote: From: Kevin Porter <[EMAIL PROTECTED]> Subject: RE: [OSL | CCIE_Voice] max session 0 - IOS Conf Bridge (failed) To: "Jacob Owen" <[EMAIL PROTECTED]>, [EMAIL PROTECTED] Cc: [email protected] Date: Sunday, November 16, 2008, 3:17 AM You must have a “free” DSP to configure any sessions for conferencing. With a PVDM2-16 you will be able to configure 2 conferencing sessions as long as nothing else has grabbed any of the channels. Transcoding will “share” DSP’s with Voice Port terminations, so I agree that it is best to configure the conferencing first, which will reserve the DSP channels first, then go to transcoding… Just for info, conferencing profiles grab 8 channels of a PVDM2 per session, so a PVDM2-8 will give you a 1 for “Max sessions”, a PVDM2-16 will give you a 2, PVDM2-32 gives you 4, so on and so forth, but the DSP must be “free” of any other channels being allocated… Kevin Kevin Porter Systems Engineer L4 Netelligent Corporation 400 South Woods Mill Drive, Suite 105 St. Louis , MO 63017 Office: (314) 392-6921 Cell: (314) 852-1252 Fax: (314) 392-9760 [EMAIL PROTECTED] www.netelligent.com Bridging The Gap Between Good and GREAT IP Communications! From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Jacob Owen Sent: Saturday, November 15, 2008 11:25 AM To: [EMAIL PROTECTED] Cc: [email protected] Subject: Re: [OSL | CCIE_Voice] max session 0 - IOS Conf Bridge (failed) You can also try to turn up your conference dspfarm profile first, and then the transcoder. I have run into the same issue when trying to do the transcoder first, so just "shut" on dspfarm profile 2, then "no shut" on dspfarm profile 1, and finally "no shut" on dspfarm profile 2. Let me know if that helps. On Sat, Nov 15, 2008 at 10:42 AM, Erwan Erwan <[EMAIL PROTECTED]> wrote: hi, I try to config IOS Conf Bridge and Transcode in 2811 , DSP type C5110 - Config for Transcode succeed - But config for Conference failed, it said max session 0, i think I still hv enough DSP ------------------------------------------------------------------------------------------------------------------------- voice-card 0 dspfarm dsp services dspfarm sccp ccm group 1 associate ccm 2 priority 2 associate ccm 1 priority 1 associate profile 1 register cfb001e7a5f9530 associate profile 2 register mtp001e7a5f9530 ! dspfarm profile 2 transcode codec g711ulaw codec g729r8 maximum sessions 2 associate application SCCP ! dspfarm profile 1 conference codec g711ulaw codec g729r8 associate application SCCP shutdown --------------------------------------------------------------- NAME: "PVDMII DSP SIMM with one DSP", DESCR: "PVDMII DSP SIMM with one DSP" PID: PVDM2-16 , VID: V01 , SN: FOC11110D7C NAME: "High Density Voice", DESCR: "High Density Voice" PID: NM-HDV= , VID: 1.1, SN: JAB05400BRG NAME: "PVDM 3-C549 Simm", DESCR: "PVDM 3-C549 Simm" PID: PVDM-12= , VID: 1.1, SN: NAME: "PVDM 3-C549 Simm", DESCR: "PVDM 3-C549 Simm" PID: PVDM-12= , VID: 1.1, SN: Thks -- Jacob Owen CCIE #14063 (R&S, Voice, Service Provider), CCDP
