Hi Art, You was right. I found the message in "future broadcasts". I shall listen to that lady. I allways ignored her :) After I am loging to Broadcast Administrator I am presssing "3" and the lady is telling me "the system has x future broadcast messages". I tested this today in my personal lab. I will test it once again, tommorow, on ProctoLabs Rack. Thank you so much. If I could rate you I will give 5 stars for this answer. This is the normal setup(HQ in PST and CME in GMT +8 timezone) but yestarday was the first time when I set timezones correctly:)
Many thanks once again, Cristian P.S: I will let you know about my tests on same Rack. ________________________________ From: [email protected] [mailto:[email protected]] On Behalf Of Art Sandborgh Sent: Monday, June 08, 2009 10:19 PM To: ccie list Subject: Re: [OSL | CCIE_Voice] VPIM Broadcast CUE-->UNITY Christian, I have seen this symptom before, but I do not know if you are experiencing the same cause. I fought for hours trying to figure out why the messages did not arrive, when in reality they had (but had not been distributed to the mailboxes yet). If your NTP for the 852 site is set to an earlier timezone ( say +8) and you send the message to a later timezone (say -5) marked "immediate" it gets stored in the "future broadcasts". The only way I know of to check is to dial into the Broadcast Administrator and check for pending messages (I think that is the menu selection. You should find it there if you are experiencing what I did. Good Luck! Art Message: 5 Date: Mon, 8 Jun 2009 14:57:27 +0300 From: Cristi Radescu <[email protected]> Subject: [OSL | CCIE_Voice] VPIM Broadcast CUE-->UNITY To: "[email protected]" <[email protected]> Message-ID: <21c0dae06d627846bbfeebed4c4da65622595b9...@cre-exch.csc.crescendo.ro> Content-Type: text/plain; charset="us-ascii" Hi all, Today I had a strange problem on a ProctorLabs rack. I couldn't nail VPIM Broadcast from CUE to Unity. I did this many times before but today it didn't work. Normal VPIM message is working perfect. Please see below related config on CUE: network location id "104" email domain voip.lab name "UNITY-LAB" voicemail broadcast vpim-id 1111 end location network location id "852" email domain cciev.com name "cue" voicemail broadcast vpim-id 3333 end location network local location id 852 In Unity I had normal stuff for VPIM configured. Normal VPIM works in both directions. Broadcast VPIM from Unity to CUE works. I have ping in unity-lab.voip.lab from CUE. Debug from CUE looks ok: 961 06/08 15:16:52.293 netw vpim 3 VPIM: To: <[email protected]> 8961 06/08 15:16:52.297 netw vpim 3 VPIM: From: cme<[email protected]> 8961 06/08 15:16:52.303 netw vpim 3 VPIM: Date: Mon, 08 Jun 2009 15:16:51 +0100 (BST) 8961 06/08 15:16:52.304 netw vpim 3 VPIM: MIME-Version: 1.0 (Voice 2.0) 8961 06/08 15:16:52.305 netw vpim 3 VPIM: Content-Type: Multipart/Voice-Message; Version=2.0; 8961 06/08 15:16:52.306 netw vpim 3 VPIM: Boundary="==VpimMsg==1244470612233" 8961 06/08 15:16:52.307 netw vpim 3 VPIM: Content-Transfer-Encoding: 7bit 8961 06/08 15:16:52.308 netw vpim 3 VPIM: Message-ID: <FHK0849F1CY-AIM-FOC11200C37-1244468200983-NBCM> 8961 06/08 15:16:52.311 netw vpim 3 VPIM: Subject: Broadcast Message from CUE Location 852 8961 06/08 15:16:52.311 netw vpim 3 VPIM: X-CISCO-SBM-ID: FHK0849F1CY-AIM-FOC11200C37-1244468200983-NBCM 8961 06/08 15:16:52.317 netw vpim 3 VPIM: X-CISCO-SBM-START-TIME: Mon, 08 Jun 2009 15:16:51 +0100 (BST) 8961 06/08 15:16:52.324 netw vpim 3 VPIM: X-CISCO-SBM-END-TIME: Wed, 08 Jul 2009 15:16:44 +0100 (BST) 8961 06/08 15:16:52.325 netw vpim 3 VPIM: X-CISCO-SBM-CUSTOM1: 61EF9907D84E295ADB9E2F9951F79543 8961 06/08 15:16:52.326 netw vpim 3 VPIM: 8961 06/08 15:16:52.327 netw vpim 3 VPIM: --==VpimMsg==1244470612233 8961 06/08 15:16:52.328 netw vpim 3 VPIM: Content-Type: Audio/32KADPCM 8961 06/08 15:16:52.329 netw vpim 3 VPIM: Content-Transfer-Encoding: Base64 8961 06/08 15:16:52.331 netw vpim 3 VPIM: Content-Description: VPIM Message 8961 06/08 15:16:52.331 netw vpim 3 VPIM: Content-Disposition: inline; voice=Voice-Message 8961 06/08 15:16:52.332 netw vpim 3 VPIM: Content-ID: FHK0849F1CY-AIM-FOC11200C37-1244468200983-NBCM 8961 06/08 15:16:52.333 netw vpim 3 VPIM: ............... Anyone faced it before? I changed "broadcast message verify interval" at 1 minute, I waited 10 minutes probably but ... nothing. Any idea would be highly appreciated, Cristian -------------- next part -------------- An HTML attachment was scrubbed... URL: http://onlinestudylist.com/pipermail/ccie_voice/attachments/20090608/5ae57eab/attachment.htm ------------------------------ _______________________________________________ CCIE_Voice mailing list [email protected] http://onlinestudylist.com/mailman/listinfo/ccie_voice End of CCIE_Voice Digest, Vol 40, Issue 28 ****************************************** ________________________________ Lauren found her dream laptop. Find the PC that's right for you.<http://www.microsoft.com/windows/choosepc/?ocid=ftp_val_wl_290>
