Hello, Calling the pilot number of a BACD script, after like 5 sec i get a bust tone. Below ids the config. any one with an idea of what might be missing R2-RTR(config)#do wr Building configuration... [OK] BR2-RTR(config)#do sh run Building configuration... Current configuration : 5530 bytes ! ! Last configuration change at 04:58:19 CET Wed Nov 4 2009 ! NVRAM config last updated at 05:10:34 CET Wed Nov 4 2009 ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname BR2-RTR ! boot-start-marker boot system flash:c2800nm-adventerprisek9-mz.124-22.T.bin warm-reboot boot-end-marker ! card type t1 0 1 logging message-counter syslog logging buffered 4096 ! no aaa new-model memory-size iomem 20 clock timezone CET 1 clock summer-time CET recurring 1 Sun Apr 1:00 last Sun Oct 1:00 network-clock-participate wic 0 no network-clock-participate wic 1 ! dot11 syslog ip source-route ! ! ip cef ! ! no ip domain lookup no ipv6 cef multilink bundle-name authenticated ! ! ! ! isdn switch-type primary-net5 ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip ! ! ! ! ! ! ! ! ! ! ! ! ! voice hunt-group 1 parallel final 3600 list 3001,3002 pilot 3210 ! ! ! voice translation-rule 1 rule 1 /^32143/ /3/ ! ! voice translation-profile in translate called 1 ! ! voice-card 0 dsp services dspfarm ! ! application service queue flash:bacdprompts/app-b-acd-aa-2.1.2.2.tcl param aa-hunt3 3210 param queue-len 10 param aa-hunt10 3002 param queue-manager-debugs 1 param number-of-hunt-grps 2 ! service aa flash:bacdprompts/app-b-acd-2.1.2.2.tcl paramspace english index 1 param number-of-hunt-grps 2 param handoff-string aa param dial-by-extension-option 1 paramspace english language en param max-time-vm-retry 2 param aa-pilot 3500 paramspace english location flash:bacdprompts param second-greeting-time 60 param welcome-prompt _bacd_welcome.au param call-retry-timer 15 param voice-mail 3600 param max-time-call-retry 90 param service-name queue ! ! ! ! ! ! archive log config hidekeys ! ! controller E1 0/0/0 pri-group timeslots 1-3,16 service mgcp ! controller E1 0/0/1 ! controller T1 0/1/0 cablelength long 0db channel-group 0 timeslots 1-24 ! ! ! ! ! interface Loopback0 ip address 10.10.110.3 255.255.255.255 ip ospf network point-to-point ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface Service-Engine0/0 ip unnumbered Vlan400 service-module ip address 10.10.202.2 255.255.255.0 service-module ip default-gateway 10.10.202.1 ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/3/0 switchport trunk native vlan 200 switchport mode trunk switchport voice vlan 400 ! interface FastEthernet0/3/1 shutdown ! interface FastEthernet0/3/2 shutdown ! interface FastEthernet0/3/3 shutdown ! interface Serial0/0/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice voice no cdp enable ! interface Serial0/1/0:0 no ip address encapsulation frame-relay IETF no fair-queue frame-relay lmi-type ansi ! interface Serial0/1/0:0.1 point-to-point ip address 10.10.112.2 255.255.255.0 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 102 ! interface Vlan1 no ip address ! interface Vlan200 ip address 10.10.102.1 255.255.255.0 ! interface Vlan400 ip address 10.10.202.1 255.255.255.0 ip helper-address 10.10.200.3 ! router ospf 1 router-id 10.10.202.1 log-adjacency-changes network 10.10.0.0 0.0.255.255 area 0 ! ip forward-protocol nd ip route 10.10.202.2 255.255.255.255 Service-Engine0/0 ! no ip http server no ip http secure-server ! ! ! ! ! tftp-server music-on-hold.au ! control-plane ! ! ! voice-port 0/0/0:15 translation-profile incoming in ! ccm-manager switchback immediate ccm-manager fallback-mgcp ccm-manager mgcp ccm-manager fax protocol cisco ccm-manager music-on-hold ! mgcp mgcp call-agent 10.10.210.11 service-type mgcp version 0.1 mgcp dtmf-relay voip codec all mode out-of-band mgcp fax t38 ecm mgcp bind control source-interface Loopback0 mgcp bind media source-interface Loopback0 ! mgcp profile default ! sccp local Vlan400 sccp ccm 10.10.210.10 identifier 2 version 5.0.1 sccp ccm 10.10.210.11 identifier 1 version 5.0.1 sccp ! sccp ccm group 1 bind interface Vlan400 associate ccm 1 priority 1 associate ccm 2 priority 2 associate profile 1 register br2transcoder ! dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 3 associate application SCCP ! ! dial-peer voice 1 pots incoming called-number . direct-inward-dial ! dial-peer voice 100 voip destination-pattern 3[06]00 session protocol sipv2 session target ipv4:10.10.202.2 codec g711ulaw no vad ! dial-peer voice 3500 voip service aa destination-pattern 3500 session target ipv4:10.10.202.1 incoming called-number 3500 dtmf-relay h245-alphanumeric codec g711ulaw no vad ! ! ! call-manager-fallback max-conferences 8 gain -6 transfer-system full-consult ip source-address 10.10.202.1 port 2000 max-ephones 2 max-dn 2 moh music-on-hold.au ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line 194 no activation-character no exec transport preferred none transport input all transport output all line vty 0 4 exec-timeout 0 0 privilege level 15 logging synchronous no login transport preferred none transport input telnet line vty 5 15 exec-timeout 0 0 privilege level 15 logging synchronous no login transport preferred none transport input telnet ! scheduler allocate 20000 1000 ntp server 10.10.100.2 end
BR2-RTR(config)# thanks
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
