Do you have a dns server that is reachable from sub?
Can you sniff the packets and post a capture?
Sent from my phone
On Mar 3, 2010, at 10:24 AM, ShinGei Yong <[email protected]>
wrote:
Hi Bill,
Thanks for spotting out the difference between the naming of the
nodes. Has been re-verify again the the node's naming and the
confirmed the hostname is correct throughout the setup. The naming
for Sub is under_scroll instead of hypen on the VM Console was just
because its a naming of the VM console.
Applying a upgrade patch on CUCM under VM platform don't think is
possible. In fact, i didn't apply ANY patches to the CUCM-PUB, so am
sure the both the CUCM-PUB and CUCM-SUB version are same.
Anymore possible solution coming?
Thanks
Shingei
On Tue, Mar 2, 2010 at 3:18 PM, Bill Talley <[email protected]>
wrote:
Are you sure hostnames are correct? On the previous screenshot
your CUCM-PUB servername has a hyphen between CUCM-PUB, however, you
vmware console window for your sub has CUCM_SUB. Is by chance your
PUB hostname CUCM_PUB, with an underscore instead of a hyphen?
Any chance you had applied a patch to the PUB previously and it's no
longer version 7.0.1.11000-2? I've never tried installing a sub
with a different version so I'm not sure what the error would be
that is generated in that scenario.
On Mar 2, 2010, at 12:59 AM, ShinGei Yong wrote:
Hi Roger, Berry,
Am already did that a few times, adding, removing and re-adding the
CUCM-Sub into the cluster inventory, but still got no chance to get
it work.
I think i've out of my mind, can't think of any possibilities.
Anyone else can help?
Thanks
Shingei
On Mon, Mar 1, 2010 at 9:35 PM, Berry, Matthew J. <[email protected]
> wrote:
Good point, Roger. CUCM Pub needs something to validate against.
- Sent from my Blackberry
From: [email protected] <[email protected]
>
To: ShinGei Yong <[email protected]>; [email protected]
<[email protected]>
Sent: Mon Mar 01 04:27:15 2010
Subject: Re: [OSL | CCIE_Voice] Failure of Adding subscriber-VM
Server 2.0
Hi Shingei,
This maybe a long shot, but anyway, have you added the sub as a UCM
server on the pub before you tried to add it as a 2nd node?
Roger Källberg
Unified Communication Consultant
Cygate AB
From: ShinGei Yong [mailto:[email protected]]
Sent: den 1 mars 2010 03:29
To: [email protected]
Subject: [OSL | CCIE_Voice] Failure of Adding subscriber-VM Server
2.0
Hi All,
Im currently having the issue of adding the 2nd node to the UCM
cluster. The error message as per attached jpg "Configuration
Validation with CUCM-PUB Failed".
I've did some research based on the error message, either from
CISCO or some older post. What i've tried out was:
1. Adding a NTP server to CUCM-PUB. CUCM-PUB was able to get the
time source from my WINXP modified NTP server, and can be viewed
from CUCM CLI.
2. Changed of Security Password. Based on CISCO explanation, it
could be due to the security password mismatch between CUCM-PUB and
SUB. I've reset the security password and reboot the CUCM-PUB, but
still got no luck. I did tried to input an "incorrect" Security
Password while adding the 2nd node, it did correctly prompt that
the password was error. So confirmed that the security password
entered was correct.
3. Some post mentioned that the MTU for the CUCM, will have some
issue if leave it to default, but i'm not too sure what does it
mean? Should i change it to MTU size to 1492?
I'm currently using VMWare Server 2.0.
regards,
Shingei
_______________________________________________
For more information regarding industry leading CCIE Lab training,
please visit www.ipexpert.com
____________________________
Bill Talley
IP Telephony Consultant
Alexander Open Systems, Inc
12851 Foster, Suite 200
Overland Park, KS 66213
(913) 307-2330, Scheduling Group
(913) 307-2380, Fax
[email protected]
http://www.aos5.com
CONFIDENTIALITY NOTICE: This electronic mail transmission (including
any accompanying attachments) is intended solely for its authorized
recipient(s), and may contain confidential and/or legally privileged
information. If you are not an intended recipient, or responsible
for delivering some or all of this transmission to an intended
recipient, be aware that any review, copying, printing,
distribution, use or disclosure of the contents of this message is
strictly prohibited. If you have received this electronic mail
message in error, please delete it from your system without copying
it, and contact sender immediately by Reply e-mail, or by calling 913-307-2300
, so that our address records can be corrected.
Although this e-mail and any attachments are believed to be free of
any virus or other defect that might negatively affect any computer
system into which it is received and opened, it is the
responsibility of the recipient to ensure that it is virus free and
no responsibility is accepted by the sender for any loss or damage
arising in any way in the event that such a virus or defect exists.
_______________________________________________
For more information regarding industry leading CCIE Lab training,
please visit www.ipexpert.com
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
