Hi Kobel, Not sure i'm understand your question correctly. But i believe the VM Pilot information already stated, it used CSS-UC-VMPORT (PT-VMPORT,INT-DN) as below.
Shingei On Wed, Dec 8, 2010 at 6:48 PM, Miron Kobelski <[email protected]> wrote: > OK, but it is not assigned to the VM pilot? > > > > > 2010/12/8 ShinGei Yong <[email protected]> > >> Hi Kobel, >> >> i believed is already stated there, the CSS-INT-DN which comprised ( >> INT-DN and UC-VMPILOT) as well >> >> >> Shingei >> >> >> On Wed, Dec 8, 2010 at 6:42 PM, Miron Kobelski <[email protected]>wrote: >> >>> It seems you don't have the PT-UC-VMPILOT partition in the CSS used for >>> forwarding - this might be your issue. >>> >>> regards >>> kobel >>> >>> >>> On Wed, Dec 8, 2010 at 11:39, ShinGei Yong <[email protected]>wrote: >>> >>>> Hi Kobel, >>>> >>>> Below is the setup: >>>> >>>> 5600/PT-UC-VMPILOT >>>> 5601/PT-UC-VMPORT >>>> 5602/PT-UC-VMPORT >>>> >>>> 5001/PT-INT-DN (Phone B) >>>> 5002/PT-INT-DN (Phone A) >>>> >>>> CSS-INT-DN (PT-INT-DN,PT-UC-VMPILOT) >>>> CSS-UC-VMPORT (PT-VMPORT,PT-INT-DN) >>>> >>>> Voicemail Pilot Information >>>> Pilot Number: 5600 >>>> CSS: CSS-UC-VMPORT >>>> >>>> Phone A Line Setting: >>>> CFA (Checked) CSS-INT-DN >>>> CFB (Checked) CSS-INT-DN >>>> CFNA (Checked) CSS-INT-DN >>>> >>>> Both phone A & B able to dial VM directly without issue. >>>> >>>> Anything goes wrong? >>>> >>>> Shingei >>>> >>>> >>>> On Wed, Dec 8, 2010 at 5:59 PM, Miron Kobelski <[email protected]>wrote: >>>> >>>>> Hi, >>>>> >>>>> If you entered forward destination as a number, you need to also >>>>> configure proper forwarding CSS. >>>>> if you configured forwarding for the line using the VM checkbox, you >>>>> also need to have proper CSS in VM pilot. >>>>> >>>>> HTH >>>>> kobel >>>>> >>>>> >>>>> 2010/12/8 ShinGei Yong <[email protected]> >>>>> >>>>> Hi, >>>>>> >>>>>> Yes, both the cfna and cfb has already checked on line setting, and >>>>>> CSS that contain the internal DN and VM pilot did assigned also. >>>>>> >>>>>> It seem to be a CSS issue but can't figure out the cause. >>>>>> >>>>>> I tried monitor the UC port status, there is no any call answering. So >>>>>> the call just stuck some where in UCM >>>>>> >>>>>> Shingei >>>>>> >>>>>> >>>>>> >>>>>> On Wed, Dec 8, 2010 at 5:19 PM, mark.f.bunch >>>>>> <[email protected]>wrote: >>>>>> >>>>>>> Have you also configured the Calling Search Space on the line for CFA >>>>>>> and CFNA? >>>>>>> >>>>>>> >>>>>>> On 08/12/2010, at 8:12 PM, Stanislav Braichuk < >>>>>>> [email protected]> wrote: >>>>>>> >>>>>>> Are you set checkbox on cfna and cfb in line configuration? >>>>>>> >>>>>>> 2010 12 8 10:44 пользователь "ShinGei Yong" <<[email protected]> >>>>>>> [email protected]> написал: >>>>>>> > Hi, >>>>>>> > I'm facing an issue which is either cfna or cfb failed on phone A >>>>>>> when >>>>>>> > caller B call to caller A. >>>>>>> > Both the phone A and B able to access to their voicemail box in UC >>>>>>> by >>>>>>> > pressing the >>>>>>> > voicemail button and enter correct pin. >>>>>>> > >>>>>>> > Both the phone is able to dial the Pilot number directly without >>>>>>> issue. >>>>>>> > UC is integrate with UCM with SCCP. >>>>>>> > >>>>>>> > Am i miss out any setting? >>>>>>> > >>>>>>> > Shingei >>>>>>> >>>>>>> _______________________________________________ >>>>>>> For more information regarding industry leading CCIE Lab training, >>>>>>> please visit <http://www.ipexpert.com>www.ipexpert.com >>>>>>> >>>>>>> >>>>>> >>>>>> _______________________________________________ >>>>>> For more information regarding industry leading CCIE Lab training, >>>>>> please visit www.ipexpert.com >>>>>> >>>>>> >>>>> >>>> >>> >> >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
