I just tried it and this is what happens I reloaded the router and i don't have connectivity to BR1 now, so i started on the HQ router this is how my interface looks before i make the change
interface Serial0/0/1:0.1 point-to-point
bandwidth 384
ip ospf mtu-ignore
snmp trap link-status
frame-relay interface-dlci 201 ppp Virtual-Template200
class AutoQoS-FR-Se0/0/1:0-201
auto qos voip trust fr-atm
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#interface Serial0/0/1:0.1 point-to-point
R1(config-subif)#sh
R1(config-subif)#no frame-relay interface-dlci 201 ppp Virtual-Template200
as soon as I enter that command
I get the Errors below:
no frame-relay interface-dlci 201 ppp Virtual-Template200
^
% Invalid input detected at '^' marker.
AutoQoS Error: the following command could not be parsed:
no frame-relay interface-dlci 201 ppp Virtual-Template200
R1(config-subif)#
*May 31 01:51:19.535: %LINK-5-CHANGED: Interface Virtual-Template200,
changed state to administratively down
R1(config-subif)#
When I try to re-enter the Command on the sub interface
this is what i get:
R1(config-subif)#frame-relay interface-dlci 201 ppp Virtual-Template200
%vtemplate error; failed to set up PPP-FR circuit
R1(config-subif)#
and my interface looks like this :
!
interface Serial0/0/1:0.1 point-to-point
bandwidth 384
ip address 10.10.111.1 255.255.255.0
ip ospf mtu-ignore
shutdown
snmp trap link-status
end
2011/5/30 Friderich Claude <[email protected]>
> For MLP LFI, if you create the virtual-template manually (no auto-qos),
> it’s going to work.
>
> If not, just got to “frame-relay interface-dlci 102 ppp
> Virtual-Template200” and put no frame-relay interface-dlci 102 ppp
> Virtual-Template200
>
> Shut the serial interface.
>
> Put frame-relay interface-dlci 102 ppp Virtual-Template200 again and no
> shut the Serial Interface.
>
> Do this manipulation on the 2 sites configured with MLP.
>
>
>
> But for the Lab, normally you just have to reload the routers to make it
> work.
>
> Check with show policy-map interface to make sure that the policy-map is
> good configured and that you have traffic for sig and RTP
>
>
>
> Regards,
>
>
>
> *Claude Friderich*
>
> *PreSales Support*
>
> *CCIE Voice #29035*
>
> *[image: CCIEVoice_UseLogo]***
>
> *NETCORE PSF S.A.***
>
> 49 rue du Baerendall
>
> B.P.65 L-8201 Mamer
>
> Téléphone: +352 31 33 80 407
>
> Fax: +352 31 33 80 412
>
> GSM: +352 621 303 616
>
> E-mail: [email protected]
>
>
>
> *From:* Cristobal Priego [mailto:[email protected]]
> *Sent:* lundi 30 mai 2011 22:13
> *To:* Bill Lake
> *Cc:* Friderich Claude; adam compton; [email protected]
>
> *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
>
>
>
> do you recall the subject ?
> I can't find it
> i found some qos discussions, however it was related to LAN qos
>
> thank you
>
> 2011/5/30 Bill Lake <[email protected]>
>
> I believe it was about the first week of May ;)
>
>
>
> On Mon, May 30, 2011 at 11:52 AM, Friderich Claude <[email protected]>
> wrote:
>
> Hi,
>
>
>
> Look at the forum history, I spoke about this issue and how to manage and
> resolve this issue a couple of week ago …. ;-)
>
>
>
> *Claude Friderich*
>
> *PreSales Support*
>
> *CCIE Voice #29035*
>
> *[image: CCIEVoice_UseLogo]*
>
> *NETCORE PSF S.A.*
>
> 49 rue du Baerendall
>
> B.P.65 L-8201 Mamer
>
> Téléphone: +352 31 33 80 407
>
> Fax: +352 31 33 80 412
>
> GSM: +352 621 303 616
>
> E-mail: [email protected]
>
>
>
> *From:* [email protected] [mailto:
> [email protected]] *On Behalf Of *adam compton
> *Sent:* lundi 30 mai 2011 15:45
> *To:* Cristobal Priego
> *Cc:* [email protected]
> *Subject:* Re: [OSL | CCIE_Voice] auto qos voip trust fr-atm
>
>
>
> I've noticed that if you reload BR1 router, it takes a long time for OSPF
> to populate the routes again. I've had to wait like 5-10 minutes before for
> the routes to get back on the router. That could possibly be what you're
> seeing. If that is the case, you should be able to ping the serial
> interfaces between HQ and BR1, but nothing else on HQ or BR2.
>
>
>
> Adam Compton
>
> On Sun, May 29, 2011 at 11:44 PM, Cristobal Priego <
> [email protected]> wrote:
>
> hello all
>
> while doing a mock lab
> i needed to configure LLQ, MLP LFI cRTP between BR1 and HQ, the bw was 384
>
> when i issued auto qos voip trust fr-atm on both interfaces, after setting
> the BW on the inferfaces
> everything was great, no problem
>
> however once i reloaded the BR1 router
> i lost connectivity to the HQ site
>
> i reloaded HQ router and still no connectivity
>
>
> so i reverted my pod
>
> and resstarted again only with QOS
>
> i set the BW
> and ran the command again
> without any customization
>
> and the same issue happened, where i lost connectivity from BR1 to HQ
>
> do you guys know how to fix this ?
>
> thank you
>
> _______________________________________________
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
> Are you a CCNP or CCIE and looking for a job? Check out
> www.PlatinumPlacement.com <http://www.platinumplacement.com/>
>
>
>
>
> _______________________________________________
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
> Are you a CCNP or CCIE and looking for a job? Check out
> www.PlatinumPlacement.com
>
>
>
>
>
<<image004.jpg>>
<<image003.jpg>>
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
