NTP Server can be configured in CUE either during the Initial Setup. Or later, through the CLI
On Thu, Jan 5, 2012 at 5:28 AM, Randall Crumm <rrcr...@yahoo.com> wrote: > HI All, > Thanks for the replies. > > I do need NTP master 9 since the question is requiring the local clock as > backup. > I was able to ping the lo0 interface for sa-rtr > so my commands I put in are: > ntp master 9 > ntp server 10.10.110.1 > > Here is my question. If i did not configure ntp server 10.10.110.3 (as > above), then should I be manually put it in the CUE wizard config? > > Thanks, > Randall > > > ------------------------------ > *From:* Bill Lake <whl...@gmail.com> > *To:* Matthew Saskin <m...@saskin.net> > *Cc:* Online Study <ccie_voice@onlinestudylist.com> > *Sent:* Wednesday, January 4, 2012 4:10 PM > *Subject:* Re: [OSL | CCIE_Voice] New Lab #2 - CUE ntp > > You do not need the ntp master command and it can actually cause the ntp > to not work > > remove the ntp master command (by default your router automatically > answers ntp request out every interface once you do the ntp server <ip> > command > > verify that your BR2 router is synced with ntp server at 10.10.110.1 and > if not set the times as close to the same as you can and that helps speed > up sync > > once sync is complete, make sure you can ping both addresses, sometimes > things are shut down such as is service-engine shut down? verify this with > show ip int br > > once you can ping the cue ip and have ntp sync complete, you should not > get this error > > > > > > On Wed, Jan 4, 2012 at 3:41 PM, Matthew Saskin <m...@saskin.net> wrote: > > Also, make sure that 10.10.110.3 is indeed acting as an NTP server. If > it's a router, "ntp master" and "ntp source" to the interface that has the > IP 10.10.110.3, etc. > > I know that I typically forget to put the static route back to the CUE > module since you can get session/console access with the service-module > ip/default gateway set, but no external traffic without the static route. > > -matthew > > On Wed, Jan 4, 2012 at 3:14 PM, datucha123 datucha123 < > datucha...@gmail.com> wrote: > > ping 10.10.110.3 - and see if it pings. > > then take a look at the Integrated Service Engine Interface, to see the > default gateway set. > > On Thu, Jan 5, 2012 at 12:03 AM, Rrcrumm <rrcr...@yahoo.com> wrote: > > What commands? > > Sent from my iPhone > > On Jan 4, 2012, at 11:53 AM, datucha123 datucha123 <datucha...@gmail.com> > wrote: > > Verify that CUE can reach the NTP IP Address. and the CUE module has the > default gateway set > > On Wed, Jan 4, 2012 at 11:27 PM, Randall Crumm <rrcr...@yahoo.com> wrote: > > HI, > I am working on the new lab #2. > > When configuring CUE the question asks for the primary NTP server to be > 10.10.110.3. The default is lo1, 10.10.115.1 > > When I enter that IP address, I get an error : > > I could not reach 10.10.110.3 using NTP. > If 10.10.110.3 really is an NTP server, then > there may be a firewall blocking NTP packets. > NTP uses UDP port 123. > > > Any thoughts? > > > Thanks, > Randall > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com <http://www.platinumplacement.com/> > > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com <http://www.platinumplacement.com/> > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com <http://www.platinumplacement.com/> > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com <http://www.platinumplacement.com/> > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com <http://www.platinumplacement.com/> >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
