I advise against using codec pass through on the MTP. I'd recommend something like the following:
dspfarm profile 2 mtp no codec g711u codec g729r8 max sess softw <some number> assoc app sccp no shut dspfarm profile 3 transcod codec g729r8 max sess <some number> assoc app sccp no shut ! ccm group 1 ..stuff.. assoc prof 2 register sc-rsvp assoc prof 3 register sc-xocder ..stuff.. ! -Bill -- William Bell blog: http://ucguerrilla.com twitter: @ucguerrilla On Mar 20, 2013, at 7:20 PM, Vikky Kumar wrote: > Willam, > BR2 is CUCM site, and there is integration b/w CUE - CUCM > > I have configured RSVP, rsvp bandwidth = 136 kbps on both sides > > When i call HQ phone to BR2-CUE it gives fast busy tone and give "Ring out" > display on HQ Phones > > > pt. b. transcoder in a MRG and MRGL that is assigned to CUE CTI devices (use > Device Pool) ... Done Already > pt. c. i want codec g729 between sites, hence under MTP i selected only > codec g729r8 + codec pass thru > > > ?? still prob.. > > Regards, > > Vikas > > > > > On Thu, Mar 21, 2013 at 12:53 AM, William Bell <b...@ucguerrilla.com> wrote: > Vikky, > > Please clarify. You say you have configured Branch 2 as CME and CUE. Then you > say CUE is registered to CUCM. That doesn't jive for me. Perhaps I am > mis-reading or mis-interpreting that part of the question. > > You also say you are doing CAC between HQ and Branch 2. Is this locations > based CAC or RSVP? > > Finally, when you say you can't call CUE. What does that mean? Do you get a > fast busy? Annunciator? Does it ring and fail? > > > Others have touched on the key points and the natural inclination is to look > at CODEC since Branch 2 phones <--> CUE work fine. > > If Branch 2 is a CUCM site then you have to: > > a. Create transcoder at Branch 2. Looks like you have done this > > b. Make sure you have that transcoder in a MRG and MRGL that is assigned to > CUE CTI devices (use Device Pool) > > c. If you are using RSVP. Make sure you provision the same codec under the > software MTP resource as you expect to have on the WAN and that matches one > of the codecs supported by the transcoder. > > > The "allow connections" under voice service voip shouldn't come into play in > a CUE-CUCM integration because the CUE-CUCM integration isn't SIP nor is it > H323. It is TAPI. > > > > > > > > -- > William Bell > blog: http://ucguerrilla.com > twitter: @ucguerrilla > > > > On Mar 20, 2013, at 2:16 PM, Vikky Kumar wrote: > >> Hi Experts, >> >> I configured branch 2 CME/CUE working normal for Voice mails. >> >> CUE is registered with CUCM but I call not call CUE(6220) from HQ and >> Branch1 but branch2 phones 4001 and 4002 working normal/ringing from every >> where. >> >> FYI. I have also configured CAC between on Br2 site - HQ site >> >> Please helpppp. >> >> Regards >> >> Vikky >> >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> Are you a CCNP or CCIE and looking for a job? Check out >> www.PlatinumPlacement.com > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com