I have Branch 2 site which contains Transcoder moreover all my agents are in Branch-2 site i have region matrix between other region
On Sun, Jun 16, 2013 at 4:54 PM, Bill Talley <bill.tal...@aos5.com> wrote: > Do you have a transcoder setup and being used for the call? If so, > check the SCCC connections. Otherwise you would get a busy signal if > region said g729 and CCX was set for g711. > > > > > > > Sent from an Apple iOS device with very tiny touchscreen input keys. > Please excude my typtos. > > On Jun 16, 2013, at 9:41 AM, "CISCO CCIE VOICE" <ccievoic...@gmail.com> > wrote: > > Thanks Bill,but if i Press question mark 2 time thn i can see its > taking g729 codec that fine but ths result can be due to Region not from > UCCX G729 Codec > > > On Sun, Jun 16, 2013 at 3:37 PM, Bill Talley <bill.tal...@aos5.com> wrote: > >> On the IP phone, press the question mark button twice. >> >> On the vgw, 'show call active voice compact'. >> >> *Bill Talley* >> UC Systems Consultant >> >> *Alexander Open Systems, Inc* >> 913.307.2330 (scheduling) | 913.744.3219 (direct) >> Web <http://www.aos5.com/> | Request Support<http://www.aos5.com/support> >> | >> Facebook<http://www.facebook.com/pages/Alexander-Open-Systems-AOS/109484829074064> >> | LinkedIn <http://www.linkedin.com/company/aos> >> >> >> >> >> Sent from an Apple iOS device with very tiny touchscreen input keys. >> Please excude my typtos. >> >> On Jun 16, 2013, at 8:14 AM, "CISCO CCIE VOICE" <ccievoic...@gmail.com> >> wrote: >> >> After i configure UCCX with codec g729 under service parameter,if i >> call to UCCX trigger number let say 5000 from HQ or Branch 1 or PSTN how do >> i know that this call has been using g729 uccx native codec not that from >> region >> >> >> On Sun, Jun 16, 2013 at 2:41 PM, Somphol Boonjing <somp...@gmail.com>wrote: >> >>> Hi, >>> >>> I think the easiest way is to check UCCX Service Parameters under >>> System menu. >>> >>> --Somphol. >>> >>> >>> --Somphol >>> >>> >>> On Sun, Jun 16, 2013 at 7:36 PM, CISCO CCIE VOICE < >>> ccievoic...@gmail.com> wrote: >>> >>>> Hi, >>>> >>>> How can i verify that UCCX is using G729 codec native >>>> >>>> Thanks >>>> >>>> >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, >>>> please visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com >>>> >>> >>> >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> Are you a CCNP or CCIE and looking for a job? Check out >> www.PlatinumPlacement.com >> >> >> >> CONFIDENTIALITY NOTICE: This electronic mail transmission (including any >> accompanying attachments) is intended solely for its authorized >> recipient(s), and may contain confidential and/or legally privileged >> information. If you are not an intended recipient, or responsible for >> delivering some or all of this transmission to an intended recipient, be >> aware that any review, copying, printing, distribution, use or disclosure >> of the contents of this message is strictly prohibited. If you have >> received this electronic mail message in error, please delete it from your >> system without copying it, and contact sender immediately by Reply e-mail, >> or by calling 913-307-2300, so that our address records can be corrected. >> >> Although this e-mail and any attachments are believed to be free of any >> virus or other defect that might negatively affect any computer system into >> which it is received and opened, it is the responsibility of the recipient >> to ensure that it is virus free and no responsibility is accepted by the >> sender for any loss or damage arising in any way in the event that such a >> virus or defect exists. >> >> > > > CONFIDENTIALITY NOTICE: This electronic mail transmission (including any > accompanying attachments) is intended solely for its authorized > recipient(s), and may contain confidential and/or legally privileged > information. If you are not an intended recipient, or responsible for > delivering some or all of this transmission to an intended recipient, be > aware that any review, copying, printing, distribution, use or disclosure > of the contents of this message is strictly prohibited. If you have > received this electronic mail message in error, please delete it from your > system without copying it, and contact sender immediately by Reply e-mail, > or by calling 913-307-2300, so that our address records can be corrected. > > Although this e-mail and any attachments are believed to be free of any > virus or other defect that might negatively affect any computer system into > which it is received and opened, it is the responsibility of the recipient > to ensure that it is virus free and no responsibility is accepted by the > sender for any loss or damage arising in any way in the event that such a > virus or defect exists. > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com