Hi Piyush,
I assigned HQ device pool and location setting on CTI route point and CTI
ports to HQ.
Following is isdn debug output when calling from 4002 to 4000 ( during AAR)
HQ(config)#
Jul 10 22:15:08.149: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8 callref =
0x000F
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98397
Exclusive, Channel 23
Calling Party Number i = 0x1181, '85224044011'
Plan:ISDN, Type:International
Called Party Number i = 0x91, '85224044102'
Plan:ISDN, Type:International
Jul 10 22:15:08.201: ISDN Se0/0/0:23 Q931: RX <- CALL_PROC pd = 8 callref
= 0x800F
Channel ID i = 0xA98397
Exclusive, Channel 23
HQ(config)#
Jul 10 22:15:08.329: ISDN Se0/0/0:23 Q931: RX <- ALERTING pd = 8 callref =
0x800F
Progress Ind i = 0x8088 - In-band info or appropriate now available
Jul 10 22:15:08.341: ISDN Se0/0/0:23 Q931: TX -> DISCONNECT pd = 8 callref
= 0x000F
Cause i = 0x8290 - Normal call clearing
Site C phone 2 Line 2 4102 ring and call disconnect in 2 sec.
with below error message
Jul 10 22:16:48.524: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref =
0x0048
Sending Complete
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838B
Exclusive, Channel 11
Display i = 'SiteC Phone 2'
Calling Party Number i = 0x1183, '+85224044002'
Plan:ISDN, Type:International
Called Party Number i = 0x91, '85224044010'
Plan:ISDN, Type:International
Jul 10 22:16:48.524: ISDN Se0/0/0:15 Q931: TX -> RELEASE pd = 8 callref =
0x80D5
Jul 10 22:16:48.780: ISDN Se0/0/0:15 Q931: RX <- STATUS pd = 8 callref =
0x00D5
Cause i = 0x80E202 - Message not compatible with call state or not
implemented
Call State i = 0x0C
Jul 10 22:16:48.780: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 callref =
0x8047
Jul 10 22:16:48.780: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x00D5
Basically when calling from HQ PH1 to 4000 ( in AAR) it work without any
issue.
Thanks,
Ramcharan Arya
On Tue, Jul 9, 2013 at 10:37 PM, <[email protected]> wrote:
> Hello Ram,
>
> You can assign Hq device pool and location setting to cti route point and
> cti ports..
> And assign site c device pool and location to site c phones...
>
> Regards,
> Piyush Jain
>
> Sent from my android device.
>
>
>
>
> -----Original Message-----
> From: Ramcharan Arya <[email protected]>
> To: "[email protected]" <[email protected]>
> Sent: Tue, 09 Jul 2013 7:59 AM
> Subject: [OSL | CCIE_Voice] AAR and uccx
>
> Hi,
> I have a CTI Route point 4000 and two CTI port 410x and 410y
>
>
>
> SiteC Phone 1 and SC Phone 2 are in CSQ which is assign to application and
> associated with trigger.
>
> Due to RSVP when call exceed ip rsvp bandwidth call from uccx to site
> Phones should use AAR and to over PSTN.
>
> My doubts are .
>
> What should be local and device pool of CTI ports so it should work in AAR
> when PSTN caller make call to CTI route point number 4000.
>
> Can someone please advice about this.
>
> Thanks,
> Ramcharan Arya
>
>
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
