You will not be able to bring up the pri until your mgcp gw registers to cucm. In my very first reply I assumed it was already registered but I guess I should have asked.
The most common reason for not registering is a mismatch on hostname. The gateway will register as either "hostname" (if ip domain-name not set) or " hostname.domain.com (if ip domain-name domain.com). I see your hostname is "CorpHQ" and I didn't see the ip domain-name command in yiur posted config. In this case make sure that in cucm you list the mgcp gw as "CorpHQ" exactly (I always type in the correct/matching case, I'm not sure if it is actually case sensitive but why take that chance?) Use "show inventory" on the router and make sure cucm has the correct router model and nm/wic part numbers. If still no luck (just looking at cucm), then delete the gw in cucm and recreate it. On the gateway use "ccm config server [pub ip]" and "ccm config" to tell the gateway to download the config from cucm. After it registers you can the "no ccm config" and make the pri fractional. For some basics, can you ping cucm pub and sub from the gateway? Can you ping from cucm cli to the gw lo0 ip? Do you have any qos? If yes remove qos temporarily to make sure that isn't interfering. If, after all this it still doesn't work, you should take a look at router debugs and cucm traces to determine if its a config issue or a network path issue. If debugs/traces don't show any traffic you could also run a packet capture on both router and cucm to see if you are getting any traffic at all between gw and cucm. On Oct 5, 2013 2:36 PM, "Anthony Nwachukwu" < anwachu...@accesspointafrica.com> wrote: > Now see how far I have gone. Stil have issues with Registration with CCM > and the second backup is none.**** > > ** ** > > **** > > ** ** > > CorpHQ#show ccm-manager **** > > MGCP Domain Name: CorpHQ**** > > Priority Status Host**** > > ============================================================**** > > Primary None **** > > First Backup Registering with CM 177.1.10.10**** > > Second Backup None **** > > ** ** > > Current active Call Manager: None**** > > Backhaul/Redundant link port: 2428**** > > Failover Interval: 30 seconds**** > > Keepalive Interval: 15 seconds**** > > Last keepalive sent: 23:10:43 PDT Oct 4 2013 (elapsed time: > 05:12:56)**** > > Last MGCP traffic time: 04:23:16 PDT Oct 5 2013 (elapsed time: > 00:00:23)**** > > Last failover time: 03:57:15 PDT Oct 5 2013 from (0.0.0.0)**** > > Last switchback time: 03:57:06 PDT Oct 5 2013 from (177.1.10.20) > **** > > Switchback mode: Immediate**** > > MGCP Fallback mode: Not Selected**** > > Last MGCP Fallback start time: None**** > > Last MGCP Fallback end time: None**** > > MGCP Download Tones: Disabled **** > > TFTP retry count to shut Ports: 2 **** > > ** ** > > Backhaul Link info:**** > > Link Protocol: TCP **** > > Remote Port Number: 2428**** > > Remote IP Address: 177.1.10.10**** > > Current Link State: OPEN**** > > Statistics:**** > > Packets recvd: 0**** > > Recv failures: 0**** > > Packets xmitted: 0**** > > Xmit failures: 0**** > > PRI Ports being backhauled:**** > > Slot 0, VIC 0, port 0**** > > FAX mode: cisco**** > > Configuration Error History:**** > > CorpHQ#**** > > ** ** > > *From:* Justin Carney [mailto:justin.s.car...@gmail.com] > *Sent:* 05 October 2013 18:55 > *To:* Anthony Nwachukwu > *Cc:* ccie_voice@onlinestudylist.com, (ccie_voice@onlinestudylist.com) > *Subject:* Re: [OSL | CCIE_Voice] TEI_ASSIGNED**** > > ** ** > > Did you try the steps I outlined earlier?**** > > Does "show ccm" indicate your mgcp gw is regisyered to cucm? If not check > your hostname and domain name (if set) on gw and double check the cucm > config.**** > > If so it is registered you could take it a step further and remove the > pri-group from the controller (and essentially all pri and mgcp config) > reboot, then put it all back.**** > > Also, if this is your home lab (or if you have access) what does the pstn > side of the pri config look like? Make both sides have the same isdn > switch-type and the pstn side has "isdn protocol-emulate network" under > serial interface.**** > > A reload of both routers wouldn't hurt either (before or after all the > above).**** > > Some links that may help: > http://goo.gl/QA6qaC > http://goo.gl/1ctXWS**** > > On Oct 5, 2013 10:03 AM, "Anthony Nwachukwu" <anwachu...@apafrica.com> > wrote:**** > > > CorpHQ#CorpHQ# > ISDN Se0/0/0:23 Q921: User RX <- SABMEp sapi=0 tei=0 > ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED & vsc_wants_L2_up = FALSE > ISDN Se0/0/0:23 Q921: User RX <- SABMEp sapi=0 tei=0 > ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED & vsc_wants_L2_up = FALSE > CorpHQ#CorpHQ# > ISDN Se0/0/0:23 Q921: User RX <- SABMEp sapi=0 tei=0 > ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED & vsc_wants_L2_up = FALSE > CorpHQ#CorpHQ# > ISDN Se0/0/0:23 Q921: User RX <- SABMEp sapi=0 tei=0 > ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED & vsc_wants_L2_up = FALSE > CorpHQ#CorpHQ# > ISDN Se0/0/0:23 Q921: User RX <- SABMEp sapi=0 tei=0 > ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED & vsc_wants_L2_up = FALSE > CorpHQ#CorpHQ# > ISDN Se0/0/0:23 Q921: User RX <- SABMEp sapi=0 tei=0 > ISDN Se0/0/0:23 Q921: S4_SABME: BACKHAULED & vsc_wants_L2_up = FALSE > CorpHQ#CorpHQ#**** > > ** ** > > ** ** > > ** ** > > ** ** > > ** ** > > ** ** > > ** ** > > I need help to reslove the problem with TEI_ASSIGNED on the T1 Link **** > > ** ** > > ISDN Serial0/0/0:23 interface > dsl 0, interface ISDN Switchtype = primary-ni > L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003 > Layer 1 Status: > ACTIVE > Layer 2 Status: > TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED > Layer 3 Status: > 0 Active Layer 3 Call(s) > Active dsl 0 CCBs = 0 > The Free Channel Mask: 0x80000007 > Number of L2 Discards = 0, L2 Session ID = 0 > Total Allocated ISDN CCBs = 0 > CorpHQ# **** > > ** ** > > ** ** > > ** ** > > CorpHQ#show run > Building configuration... > > > Current configuration : 3755 bytes > ! > ! Last configuration change at 23:30:37 PDT Fri Oct 4 2013 > ! NVRAM config last updated at 23:30:39 PDT Fri Oct 4 2013 > ! > version 12.4 > no service pad > no service timestamps debug uptime > no service timestamps log uptime > no service password-encryption > ! > hostname CorpHQ > ! > boot-start-marker > boot-end-marker > ! > logging message-counter syslog > enable secret 5 $1$QYKS$Z.r9xOUE1ga6IkB6fi3QU0 > ! > no aaa new-model > clock timezone PST -8 > clock summer-time PDT recurring > network-clock-participate wic 0 > network-clock-select 1 T1 0/0/0 > ! > dot11 syslog > ip source-route > ! > ! > ip cef > ! > ! > no ip domain lookup > ip multicast-routing > no ipv6 cef > ! > multilink bundle-name authenticated > ! > ! > ! > ! > isdn switch-type primary-ni > ! > ! > ! > voice service voip > sip > bind control source-interface Loopback0 > bind media source-interface Loopback0 > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > ! > voice-card 0 > ! > ! > ! > ! > ! > archive > log config > hidekeys > ! > ! > ! > ! > ! > controller T1 0/0/0 > cablelength short 133 > pri-group timeslots 1-3,24 service mgcp > description == Voice Circuit to PSTN > ! > controller T1 0/0/1 > cablelength short 133 > channel-group 0 timeslots 1-24 > description == Data Circuit to WAN > ! > ip tcp synwait-time 5 > ! > ! > ! > ! > interface Loopback0 > ip address 177.1.254.1 255.255.255.255 > ! > interface FastEthernet0/0 > description == To SW1 > no ip address > duplex auto > speed auto > ! > interface FastEthernet0/0.10 > description == Server VLAN > encapsulation dot1Q 10 > ip address 177.1.10.1 255.255.255.0 > ip pim dense-mode > ip tcp adjust-mss 1300 > ! > interface FastEthernet0/0.11 > description == Voice VLAN > encapsulation dot1Q 11 > ip address 177.1.11.1 255.255.255.0 > ip pim dense-mode > ip tcp adjust-mss 1300 > ! > interface FastEthernet0/0.12 > description == Data VLAN > encapsulation dot1Q 12 > ip address 177.1.12.1 255.255.255.0 > ip tcp adjust-mss 1300 > ! > interface FastEthernet0/0.13 > description == PSTN PHONE VLAN > encapsulation dot1Q 13 > ip address 177.1.13.1 255.255.255.0 > ip tcp adjust-mss 1300 > ! > interface FastEthernet0/1 > description === To PSTN > ip address 177.1.19.254 255.255.255.0 > duplex auto > speed auto > ! > interface Serial0/0/0:23 > no ip address > encapsulation hdlc > isdn switch-type primary-ni > isdn incoming-voice voice > isdn bind-l3 ccm-manager > no cdp enable > ! > interface Serial0/0/1:0 > description == Frame-Relay Circuit to WAN > no ip address > encapsulation frame-relay > cdp enable > no frame-relay inverse-arp > frame-relay lmi-type ansi > ! > interface Serial0/0/1:0.1 point-to-point > description == FR To BR1 > ip address 177.0.101.1 255.255.255.0 > ip pim dense-mode > snmp trap link-status > frame-relay interface-dlci 101 > ! > interface Serial0/0/1:0.2 point-to-point > description == FR To BR2 > ip address 177.0.201.1 255.255.255.0 > ip pim dense-mode > snmp trap link-status > frame-relay interface-dlci 201 > ! > router ospf 1 > log-adjacency-changes > network 0.0.0.0 255.255.255.255 area 0 > ! > ip forward-protocol nd > ip http server > no ip http secure-server > ! > ! > ! > cdp timer 6 > ! > ! > ! > ! > ! > ! > ! > control-plane > ! > ! > ! > voice-port 0/0/0:23 > ! > ccm-manager redundant-host 177.1.10.10 > ccm-manager mgcp codec-all > ccm-manager fax protocol cisco > ccm-manager music-on-hold > ! > mgcp > mgcp call-agent 177.1.10.20 service-type mgcp version 0.1 > mgcp dtmf-relay voip codec all mode out-of-band > mgcp fax t38 ecm > mgcp bind control source-interface Loopback0 > mgcp bind media source-interface Loopback0 > ! > mgcp profile default > ! > ! > ! > ! > ! > ! > gatekeeper > shutdown > ! > ! > line con 0 > exec-timeout 0 0 > privilege level 15 > logging synchronous level 0 limit 20 > line aux 0 > line vty 0 4 > exec-timeout 0 0 > privilege level 15 > password cisco > logging synchronous > no login > line vty 5 15 > exec-timeout 0 0 > privilege level 15 > logging synchronous > no login > ! > scheduler allocate 20000 1000 > ntp source Loopback0 > ntp master 13 > ntp server 177.1.254.254 > end > > CorpHQ#show isdn st > Global ISDN Switchtype = primary-ni > > %Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may > not apply > > ISDN Serial0/0/0:23 interface > dsl 0, interface ISDN Switchtype = primary-ni > L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003 > Layer 1 Status: > ACTIVE > Layer 2 Status: > TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED > Layer 3 Status: > 0 Active Layer 3 Call(s) > Active dsl 0 CCBs = 0 > The Free Channel Mask: 0x80000007 > Number of L2 Discards = 0, L2 Session ID = 0 > Total Allocated ISDN CCBs = 0 > CorpHQ# **** > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com**** >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
