I would verify that what you intended to load has been correctly loaded, by displaying / dumping 1400 et seq. If that is good, I would then instruction step to observe where execution leads. It may also be necessary to clear the processor's state and maybe issue a bus init - however, the simulator startup probably obliges. Martin
PS FWIW all the vectors and traps (0 to 400 in big handfulls) are uninitialised (by you), so any of those could take you to exciting places - eg 5271 -----Original Message----- From: Peter Ekstrom via cctalk <[email protected]> Sent: 30 October 2025 14:40 To: General Discussion: On-Topic and Off-Topic Posts <[email protected]> Cc: Peter Ekstrom <[email protected]> Subject: [cctalk] Re: Looking for a bootloader Anyone here familiar with programming the 11/23 (KDF11-A) in assembler, bare metal? I have been trying to get a very simple test program to run on it but it keeps halting on an address outside of the program. Seems to always be the same address which is why I am thinking I must be missing something. The program runs fine on an 11/23+ or 11/70. Below is the listing: 1 000000 .asect 2 014000 .=14000 3 014000 012706 002000 start: mov #2000,sp 4 014004 000240 loop: nop 5 014006 000776 br loop 6 .end I have a hardware 11/23 but for convenience I have been testing on a SIMH 11/23 by loading the binary from the simh prompt and then jumping to the start address. I have tested the same code on 11/23+ and 11/70 CPUs and it runs fine. I am working in Linux and am using the following Macro11 cross-assembler: macro11 - portable MACRO11 assembler for DEC PDP-11 Version 0.8 (07 Jul 2022) Copyright 2001 Richard Krehbiel, modified 2009 by Joerg Hoppe, modified 2015-2017,2020-2021 by Olaf 'Rhialto' Seibert. I then use the obj2bin.pl utility by Don North to convert from object format to binary load format. The following is what happens: PDP-11 simulator Open SIMH V4.1-0 Current git commit id: 29d39002 sim> set cpu 11/23 sim> load test.bin sim> g 14000 HALT instruction, PC: 005271 (HALT) sim> Am I missing some initialization parts or something? I have looked through various manuals and the processor handbook for the LSI-11 but if it is in there, I am missing it. Any pointers would be greatly appreciated. -Peter On Tue, Oct 28, 2025 at 3:38 PM Peter Ekstrom <[email protected]> wrote: > Wayne, Warner, Glenn, > > Thank you very much for your responses! > > Wayne, > > I took a look at the PDP11GUI files and it is quite complex. I setup > the GUI on a PC here and tried it against my PDP-11/23 but wasn't able > to get it to work. > Not sure what I did wrong but I am definitely keeping it, and will go > through that source a bit later. I'm sure I'll learn a lot from it. > Thank you for the tip! > > Warner, > > Right now I prefer assembler because I am trying to learn more about it. > But I glanced at the BSD loader in C and find it quite interesting. I > am going to go though that too a bit later. Thank you for this tip as > well! > > Glen, > > I did look at the sources you mentioned and they were a bit more > bite-sized. So I have tinkered with it and am actually able to use it > to boot an 11/23 in SIMH using that code. I have also cobbled together > a little boot menu and incorporated this loader there. Thank you for > those pointers! > > Thank you all! > > -Peter > > On Tue, Oct 28, 2025 at 6:38 AM Glen Slick via cctalk < > [email protected]> wrote: > >> (DU) MSCP UDA50(RAxx) disk: >> >> https://ak6dn.github.io/PDP-11/M9312/ >> >> https://ak6dn.github.io/PDP-11/M9312/23-767A9/23-767A9.mac >> >> https://ak6dn.github.io/PDP-11/M9312/23-767A9/23-767A9.lst >> >> >> >> On Mon, Oct 27, 2025, 4:48 PM Wayne S via cctalk >> <[email protected]> >> wrote: >> >> > Maybe look at pdp11gui ? >> > I think it downloads a boot loader so the code may be there. >> > <https://retrocmp.com/tools/pdp11gui> >> > PDP11GUI<https://retrocmp.com/tools/pdp11gui> >> > retrocmp.com<https://retrocmp.com/tools/pdp11gui> >> > [favicon.ico]<https://retrocmp.com/tools/pdp11gui> >> > >> > >> > >> > Sent from my iPhone >> > >> > On Oct 27, 2025, at 15:58, Peter Ekstrom via cctalk < >> [email protected]> >> > wrote: >> > >> > I am looking for the assembler listing for a bootloader for >> > booting >> from >> > MSCP disks like RD-disks. >> > Google has not been very helpful and my assembler knowledge is not >> enough >> > for me to write one from scratch. Does anyone have one they can share? >> > >> > - Peter >> > >> >
