On Tue, 2004-09-28 at 14:33 +0200, Joerg Schilling wrote: > Sasa Ostrouska <[EMAIL PROTECTED]> wrote: > > > Hello to everybody, > > > > I tried to burn a DVD and I got this error, can somebody tell me > > what is on ? Is a brocen media ? > > > > > > Calling: /usr/lib/xcdroast-0.98/bin/xcdrwrap CDRECORDPRODVD dev= "0,0,0" > > gracetime=10 fs=4096k -v driveropts=burnfree speed=16 -dao -eject -pad > > -waiti tsize=2107292s - > > > > scsidev: '0,0,0' > > scsibus: 0 target: 0 lun: 0 > > Linux sg driver version: 3.1.25 > > SCSI buffer size: 64512 > > Cdrecord-ProDVD-Clone 2.01b31 (i686-pc-linux-gnu) Copyright (C) > > 1995-2004 Jörg Schilling > > Unlocked features: ProDVD Clone > > Limited features: > > This copy of cdrecord is licensed for: > > private/research/educational_non-commercial_use > > TOC Type: 1 = CD-ROM > > Waiting for data on stdin... > > Using libscg version 'schily-0.8'. > > Driveropts: 'burnfree' > > atapi: 1 > > Device type : Removable CD-ROM > > Version : 0 > > Response Format: 2 > > Capabilities : > > Vendor_info : 'PIONEER ' > > Identifikation : 'DVD-RW DVR-K12D' > > Revision : '1.00' > > Device seems to be: Generic mmc2 DVD-R/DVD-RW. > > Current: DVD+R > > Profile: DVD+R (current) > > Profile: DVD+RW > > Profile: DVD-RW sequential overwrite > > Profile: DVD-RW restricted overwrite > > Profile: DVD-R sequential recording > > Profile: DVD-ROM > > Profile: CD-RW > > Profile: CD-R > > Profile: CD-ROM > > Using generic SCSI-3/mmc-3 DVD+R driver (mmc_dvdplusr). > > Driver flags : DVD MMC-3 SWABAUDIO BURNFREE > > Supported modes: PACKET SAO > > Drive buf size : 1605632 = 1568 KB > > FIFO size : 4194304 = 4096 KB > > Track 01: data 4115 MB padsize: 30 KB > > Total size: 4115 MB = 2107307 sectors > > Current Secsize: 2048 > > Blocks total: 2295104 Blocks current: 2295104 Blocks remaining: 187797 > > Starting to write CD/DVD at speed 2 in real SAO mode for single session. > > > > Waiting for reader process to fill input buffer ... > > input buffer ready. > > Starting new track at sector: 0 > > cdrecord.prodvd: Input/output error. write_g1: scsi sendcmd: no error > > CDB: 2A 00 00 07 2A 54 00 00 1F 00 > > status: 0x2 (CHECK CONDITION) > > Sense Bytes: 70 00 04 00 13 00 02 0E 26 01 31 E6 08 01 00 00 > > Sense Key: 0x4 Hardware Error, Segment 0 > > Sense Code: 0x08 Qual 0x01 (logical unit communication time-out) Fru 0x0 > > Sense flags: Blk 1245186 (not valid) > > cmd finished after 2.012s timeout 100s > > cdrecord.prodvd: A write error occured. > > cdrecord.prodvd: Please properly read the error message above. > > Caused either by incorrect kernel DMA setup or by a defective kernel. > > Jörg >
Yesterday I wonted to write a DVD butit ended with a different error after few sec.of writing. I think this is as I have the kernel 2.6.8.1 Am I correct ? I saw that there are some problems with that kernel. Do you have any suggestions. I can use the 2.4.27 kernel without the ide-scsi thing as this is the only way I can write the DVD's - for the CD's ide-scsi works OK. If it is a pach for the 2.6.8.1 kernel where is possible to get it ? Thanks for your time and best regards -- Sasa Ostrouska <[EMAIL PROTECTED]> -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
