Todd and Margo Chester wrote:
Todd and Margo Chester wrote:
Dear Centos-Virt:
This is actually a second request for help on the
same issue. I finally got to try what several
months ago was replayed to me and no joy was to
be had. I am afraid the original thread got stale
and also had extra, unnecessary data in it.
Guest=XP Pro, SP2
Host=CentOS5; # uname -r; 2.6.18-8.1.15.el5
VirtualBox-1.5.0_24069_rhel5-2.i586.rpm
http://www.virtualbox.org/download/1.5.0/VirtualBox-1.5.0_24069_rhel5-1.i586.rpm.run
I have two nic: eth0 is the internal network; eth1 connects to a DSL
modem.
I also have a fully functioning DHCP server on eth0 (works perfectly
with Parallels for Linux).
The directions (from hell):
http://www.virtualbox.org/download/UserManual.pdf
I am trying to set up a "host interface" network between
my XP guest and my Linux host (eth0).
I do believe I FINALLY have it figured out. I wrote myself
the following how to. Please feel free to clean it up and
make it into an "Official CentOS 5 How To".
The only problem I have left is that the Guest XP can not
browse the Host's Samba server by SMB name (IP works fine)
-T
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
T's CentOS 5 -- Virtual Box "Host Networking" bridge setup:
Note: a lot of this is taken from (with lots of refinements):
http://www.linuxweblog.com/virtualbox-host-networking
iptables: after creating br0 at etho's expense, you have to
change all references to "eth0" in your firewall
to "br0"
br0: will become the internal interface and have a "Fixed" (static)
IP address of 192.168.255.10
Support software (required);
"VBoxAddIF" from Virtual Basic
bridge-utils:
yum install bridge-utils
ftp://ftp.pbone.net/mirror/ftp.centos.org/5.0/os/i386/CentOS/bridge-utils-1.1-2.i386.rpm
~~~~~~~~~~~~~~ /etc/rc.d/rc.local ~~~~~~~~~~~~~~~
# Set permissions on /dev/net/tun such that Virtual Box can use it
/bin/chmod 0666 /dev/net/tun
/bin/chmod 777 /dev/vboxdrv
# Restart the firewall
/etc/{iamnottellingyou}
~~~ /etc/sysconfig/network-scripts/ifcfg-eth0 ~~~
DEVICE=eth0
TYPE=Ethernet
ONBOOT=yes
USERCTL=yes
IPV6INIT=no
PEERDNS=no
BRIDGE=br0
ONBOOT=yes
PROMISC=yes
~~~ /etc/sysconfig/network-scripts/ifcfg-br0 ~~~
DEVICE=br0
TYPE=Bridge
BOOTPROTO=static
BROADCAST=192.168.255.255
IPADDR=192.168.255.10
NETMASK=255.255.255.0
NETWORK=192.168.255.0
GATEWAY=192.168.255.10
ONBOOT=yes
USERCTL=yes
IPV6INIT=no
PEERDNS=no
PROMISC=yes
~~~ /etc/sysconfig/network-scripts/ifcfg-br0 ~~~
Ooops ^^^^^^^^^^^ should be ifcfg-vbox0 ^^^
IPADDR=0.0.0.0
PROMISC=yes
~~~~~~~~ Initial and permanent setup ~~~~~~~~~~~
#! /bin/bash
# load the tun module
modprobe tunvi
chmod 666 /dev/net/tun
# Create a new bridge and add the interfaces to the bridge.
brctl addbr br0
brctl addif br0 eth0
/usr/bin/VBoxDeleteIF vbox0
/usr/bin/VBoxAddIF vbox0 tony br0
brctl addif br0 vbox0
# Bring up eth0 and vbox0 in promiscuous mode
# Commended out as it should be handles in "network-scripts"
#ifconfig eth0 promisc
#ifconfig vbox0 0.0.0.0 promisc
brctl addif br0 vbox0
# Now reboot (restarting networking doesn't work)
echo "Now reboot. (I have no idea why)"
_______________________________________________
CentOS-virt mailing list
[email protected]
http://lists.centos.org/mailman/listinfo/centos-virt
_______________________________________________
CentOS-virt mailing list
[email protected]
http://lists.centos.org/mailman/listinfo/centos-virt
