Hi All,
I'm finding my write performance is less than I would have expected. After
spending some considerable amount of time testing several different
configurations I can never seems to break over ~360mb/s write even when using
tmpfs for journaling.
So I've purchased 3x Dell R515's with 1 x AMD 6C CPU with 12 x 3TB SAS & 2 x
100GB Intel DC S3700 SSD's & 32GB Ram with the Perc H710p Raid controller and
Dual Port 10GBE Network Cards.
So first up I realise the SSD's were a mistake, I should have bought the 200GB
Ones as they have considerably better write though put of ~375 Mb/s vs 200 Mb/s
So to our Nodes Configuration,
2 x 3TB disks in Raid1 for OS/MON & 1 partition for OSD, 12 Disks in a Single
each in a Raid0 (like a JBOD Fashion) with a 1MB Stripe size,
(Stripe size this part was particularly important because I found the stripe
size matters considerably even on a single disk raid0. contrary to what you
might read on the internet)
Also each disk is configured with (write back cache) is enabled and (read head)
disabled.
For Networking, All nodes are connected via LACP bond with L3 hashing and using
iperf I can get up to 16gbit/s tx and rx between the nodes.
OS: Ubuntu 12.04.3 LTS w/ Kernel 3.10.12-031012-generic (had to upgrade kernel
due to 10Gbit Intel NIC's driver issues)
So this gives me 11 OSD's & 2 SSD's Per Node.
Next I've tried several different configurations which I'll briefly describe 2
of which below,
1) Cluster Configuration 1,
33 OSD's with 6x SSD's as Journals, w/ 15GB Journals on SSD.
# ceph osd pool create benchmark1 1800 1800
# rados bench -p benchmark1 180 write --no-cleanup
--------------------------------------------------
Maintaining 16 concurrent writes of 4194304 bytes for up to 180 seconds or 0
objects
Total time run: 180.250417
Total writes made: 10152
Write size: 4194304
Bandwidth (MB/sec): 225.287
Stddev Bandwidth: 35.0897
Max bandwidth (MB/sec): 312
Min bandwidth (MB/sec): 0
Average Latency: 0.284054
Stddev Latency: 0.199075
Max latency: 1.46791
Min latency: 0.038512
--------------------------------------------------
# rados bench -p benchmark1 180 seq
-------------------------------------------------
Total time run: 43.782554
Total reads made: 10120
Read size: 4194304
Bandwidth (MB/sec): 924.569
Average Latency: 0.0691903
Max latency: 0.262542
Min latency: 0.015756
-------------------------------------------------
In this configuration I found my write performance suffers a lot to the SSD's
seem to be a bottleneck and my write performance using rados bench was around
224-230mb/s
2) Cluster Configuration 2,
33 OSD's with 1Gbyte Journals on tmpfs.
# ceph osd pool create benchmark1 1800 1800
# rados bench -p benchmark1 180 write --no-cleanup
--------------------------------------------------
Maintaining 16 concurrent writes of 4194304 bytes for up to 180 seconds or 0
objects
Total time run: 180.044669
Total writes made: 15328
Write size: 4194304
Bandwidth (MB/sec): 340.538
Stddev Bandwidth: 26.6096
Max bandwidth (MB/sec): 380
Min bandwidth (MB/sec): 0
Average Latency: 0.187916
Stddev Latency: 0.0102989
Max latency: 0.336581
Min latency: 0.034475
--------------------------------------------------
# rados bench -p benchmark1 180 seq
-------------------------------------------------
Total time run: 76.481303
Total reads made: 15328
Read size: 4194304
Bandwidth (MB/sec): 801.660
Average Latency: 0.079814
Max latency: 0.317827
Min latency: 0.016857
-------------------------------------------------
Now it seems there is no bottleneck for journaling as we are using tmpfs,
however still less then what I would expect write speed the sas disks are
barely busy via iostat..
So I thought it might be a disk bus throughput issue.
Next I completed some dd tests...
This below is in a script dd-x.sh which executes the 11 readers or writers at
once.
dd if=/dev/zero of=/srv/ceph/osd.0/ddfile bs=32k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.1/ddfile bs=32k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.2/ddfile bs=32k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.3/ddfile bs=32k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.4/ddfile bs=32k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.5/ddfile bs=32k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.6/ddfile bs=32k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.7/ddfile bs=32k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.8/ddfile bs=32k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.9/ddfile bs=32k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.10/ddfile bs=32k count=100k oflag=direct &
this gives me aggregated write throughput of around 1,135 MB/s Write.
Simular script now to test reads,
dd if=/srv/ceph/osd.0/ddfile of=/dev/null bs=32k count=100k iflag=direct &
dd if=/srv/ceph/osd.1/ddfile of=/dev/null bs=32k count=100k iflag=direct &
dd if=/srv/ceph/osd.2/ddfile of=/dev/null bs=32k count=100k iflag=direct &
dd if=/srv/ceph/osd.3/ddfile of=/dev/null bs=32k count=100k iflag=direct &
dd if=/srv/ceph/osd.4/ddfile of=/dev/null bs=32k count=100k iflag=direct &
dd if=/srv/ceph/osd.5/ddfile of=/dev/null bs=32k count=100k iflag=direct &
dd if=/srv/ceph/osd.6/ddfile of=/dev/null bs=32k count=100k iflag=direct &
dd if=/srv/ceph/osd.7/ddfile of=/dev/null bs=32k count=100k iflag=direct &
dd if=/srv/ceph/osd.8/ddfile of=/dev/null bs=32k count=100k iflag=direct &
dd if=/srv/ceph/osd.9/ddfile of=/dev/null bs=32k count=100k iflag=direct &
dd if=/srv/ceph/osd.10/ddfile of=/dev/null bs=32k count=100k iflag=direct &
this gives me aggregated read throughput of around 1,382 MB/s Read.
Next I'll lower the block size to show the results,
dd if=/dev/zero of=/srv/ceph/osd.0/ddfile bs=4k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.1/ddfile bs=4k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.2/ddfile bs=4k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.3/ddfile bs=4k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.4/ddfile bs=4k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.5/ddfile bs=4k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.6/ddfile bs=4k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.7/ddfile bs=4k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.8/ddfile bs=4k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.9/ddfile bs=4k count=100k oflag=direct &
dd if=/dev/zero of=/srv/ceph/osd.10/ddfile bs=4k count=100k oflag=direct &
this gives me aggregated write throughput of around 300 MB/s Write.
dd if=/srv/ceph/osd.0/ddfile of=/dev/null bs=4k count=100k iflag=direct &
dd if=/srv/ceph/osd.1/ddfile of=/dev/null bs=4k count=100k iflag=direct &
dd if=/srv/ceph/osd.2/ddfile of=/dev/null bs=4k count=100k iflag=direct &
dd if=/srv/ceph/osd.3/ddfile of=/dev/null bs=4k count=100k iflag=direct &
dd if=/srv/ceph/osd.4/ddfile of=/dev/null bs=4k count=100k iflag=direct &
dd if=/srv/ceph/osd.5/ddfile of=/dev/null bs=4k count=100k iflag=direct &
dd if=/srv/ceph/osd.6/ddfile of=/dev/null bs=4k count=100k iflag=direct &
dd if=/srv/ceph/osd.7/ddfile of=/dev/null bs=4k count=100k iflag=direct &
dd if=/srv/ceph/osd.8/ddfile of=/dev/null bs=4k count=100k iflag=direct &
dd if=/srv/ceph/osd.9/ddfile of=/dev/null bs=4k count=100k iflag=direct &
dd if=/srv/ceph/osd.10/ddfile of=/dev/null bs=4k count=100k iflag=direct &
this gives me aggregated read throughput of around 430 MB/s Read,
This is my ceph.conf, only difference between the configs is the journal dio =
false
----------------
[global]
auth cluster required = cephx
auth service required = cephx
auth client required = cephx
public network = 10.100.96.0/24
cluster network = 10.100.128.0/24
journal dio = false
[mon]
mon data = /var/ceph/mon.$id
[mon.a]
host = rbd01
mon addr = 10.100.96.10:6789
[mon.b]
host = rbd02
mon addr = 10.100.96.11:6789
[mon.c]
host = rbd03
mon addr = 10.100.96.12:6789
[osd]
osd data = /srv/ceph/osd.$id
osd journal size = 1000
osd mkfs type = xfs
osd mkfs options xfs = "-f"
osd mount options xfs =
"rw,noexec,nodev,noatime,nodiratime,barrier=0,inode64,logbufs=8,logbsize=256k"
[osd.0]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sda5
[osd.1]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdb2
[osd.2]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdc2
[osd.3]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdd2
[osd.4]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sde2
[osd.5]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdf2
[osd.6]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdg2
[osd.7]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdh2
[osd.8]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdi2
[osd.9]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdj2
[osd.10]
host = rbd01
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdk2
[osd.11]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sda5
[osd.12]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdb2
[osd.13]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdc2
[osd.14]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdd2
[osd.15]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sde2
[osd.16]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdf2
[osd.17]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdg2
[osd.18]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdh2
[osd.19]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdi2
[osd.20]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdj2
[osd.21]
host = rbd02
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdk2
[osd.22]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sda5
[osd.23]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdb2
[osd.24]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdc2
[osd.25]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdd2
[osd.26]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sde2
[osd.27]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdf2
[osd.28]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdg2
[osd.29]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdh2
[osd.30]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdi2
[osd.31]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdj2
[osd.32]
host = rbd03
osd journal = /tmp/tmpfs/osd.$id
devs = /dev/sdk2
---------------------
Any Ideas?
Cheers,
Quenten
_______________________________________________
ceph-users mailing list
[email protected]
http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
