Hi Sam,
I'll need help getting the osdmap and pg dump prior to addition.
I can remove the OSDs and add again if the osdmap (etc.) is not logged
somewhere.
Chad.
> Hmm, that's odd. Can you attach the osdmap and ceph pg dump prior to the
> addition (with all pgs active+clean), then the osdmap and ceph pg dump
> afterwards? -Sam
>
> ----- Original Message -----
> From: "Chad William Seys" <[email protected]>
> To: "Samuel Just" <[email protected]>, "ceph-users" <[email protected]>
> Sent: Monday, July 27, 2015 12:57:23 PM
> Subject: Re: [ceph-users] why are there "degraded" PGs when adding OSDs?
>
> Hi Sam,
>
> > The pg might also be degraded right after a map change which changes the
> > up/acting sets since the few objects updated right before the map change
> > might be new on some replicas and old on the other replicas. While in
> > that
> > state, those specific objects are degraded, and the pg would report
> > degraded until they are recovered (which would happen asap, prior to
> > backfilling the new replica). -Sam
>
> That sounds like only a few PGs should be degraded. I instead have about
> 45% (and higher earlier).
>
> # ceph -s
> cluster 7797e50e-f4b3-42f6-8454-2e2b19fa41d6
> health HEALTH_WARN
> 2081 pgs backfill
> 6745 pgs degraded
> 17 pgs recovering
> 6728 pgs recovery_wait
> 6745 pgs stuck degraded
> 8826 pgs stuck unclean
> recovery 2530124/5557452 objects degraded (45.527%)
> recovery 33594/5557452 objects misplaced (0.604%)
> monmap e5: 3 mons at
> {mon01=128.104.164.197:6789/0,mon02=128.104.164.198:6789/0,mon03=10.128.198.
> 51:6789/0} election epoch 16458, quorum 0,1,2 mon03,mon01,mon02
> mdsmap e3032: 1/1/1 up {0=mds01.hep.wisc.edu=up:active}
> osdmap e149761: 27 osds: 27 up, 27 in; 2083 remapped pgs
> pgmap v13464928: 18432 pgs, 9 pools, 5401 GB data, 1364 kobjects
> 11122 GB used, 11786 GB / 22908 GB avail
> 2530124/5557452 objects degraded (45.527%)
> 33594/5557452 objects misplaced (0.604%)
> 9606 active+clean
> 6726 active+recovery_wait+degraded
> 2081 active+remapped+wait_backfill
> 17 active+recovering+degraded
> 2 active+recovery_wait+degraded+remapped
> recovery io 24861 kB/s, 6 objects/s
>
> Chad.
>
> > ----- Original Message -----
> > From: "Chad William Seys" <[email protected]>
> > To: "ceph-users" <[email protected]>
> > Sent: Monday, July 27, 2015 12:27:26 PM
> > Subject: [ceph-users] why are there "degraded" PGs when adding OSDs?
> >
> > Hi All,
> >
> > I recently added some OSDs to the Ceph cluster (0.94.2). I noticed that
> > 'ceph -s' reported both misplaced AND degraded PGs.
> >
> > Why should any PGs become degraded? Seems as though Ceph should only be
> > reporting misplaced PGs?
> >
> > From the Giant release notes:
> > Degraded vs misplaced: the Ceph health reports from ‘ceph -s’ and related
> > commands now make a distinction between data that is degraded (there are
> > fewer than the desired number of copies) and data that is misplaced
> > (stored
> > in the wrong location in the cluster). The distinction is important
> > because
> > the latter does not compromise data safety.
> >
> > Does Ceph delete some replicas of the PGs (leading to degradation) before
> > re- replicating on the new OSD?
> >
> > This does not seem to be the safest algorithm.
> > _______________________________________________
> > ceph-users mailing list
> > [email protected]
> > http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
_______________________________________________
ceph-users mailing list
[email protected]
http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
