Folks, I installed 3.8.13-7 on my WNDR3800. I used TFTP, not the default web GUI to upload the firmware. (Note - the recommendation is now to use the web GUI.)
I then ran two installation scripts to complete the custom configuration (see these pages for passwords, time zones, SSIDs, and also 6in4 configuration) - http://www.bufferbloat.net/projects/cerowrt/wiki/Automated_Configuration_of_CeroWrt - http://www.bufferbloat.net/projects/cerowrt/wiki/IPv6_Tunnel The router seems to be working as expected. I have not tried any serious performance tests, but a quick test of ping latency under load showed that the simplest-qos.h seemed to be working. As noted above, 6in4 addresses seem to work, however, I did see a lot of error messages as a result of running the 6in4 tunnel configuration script. I've attached it to see if there's anything amiss… Thanks! Rich Brown Hanover, NH USA ------------ root@cerowrt:/tmp# sh tunnel.sh Downloading http://snapon.lab.bufferbloat.net/~cero2/cerowrt/wndr/3.8.13-7/packages/Packages.gz. Updated list of available packages in /var/opkg-lists/berlin. Package 6in4 (14-1) installed in root is up to date. Setting up HE.net tunnel Restarting network... "Device busy (-16)" messages are OK. command failed: Device or resource busy (-16) Configuration file: /var/run/hostapd-phy0.conf Using interface sw00 with hwaddr 2c:b0:5d:7f:47:6a and ssid "CEROwrt" Using interface gw00 with hwaddr 2e:b0:5d:7f:47:6b and ssid "CEROwrt-guest" command failed: Device or resource busy (-16) Configuration file: /var/run/hostapd-phy1.conf handle_probe_req: send: Resource temporarily unavailable handle_probe_req: send: Resource temporarily unavailable Using interface sw10 with hwaddr 2c:b0:5d:7f:47:6c and ssid "CEROwrt5" Using interface gw10 with hwaddr 2e:b0:5d:7f:47:6d and ssid "CEROwrt-guest5" Restarting firewall... Warning: Option @defaults[0].synflood_rate has invalid value '200' Warning: Section @rule[0] (domain) does not specify a protocol, assuming TCP+UDP * Flushing IPv4 filter table * Flushing IPv4 nat table * Flushing IPv4 mangle table * Flushing IPv4 raw table * Flushing IPv6 filter table * Flushing IPv6 mangle table * Flushing IPv6 raw table * Flushing conntrack table ... * Populating IPv4 filter table * Zone 'wan' * Zone 'lan' * Zone 'guest' * Rule 'domain' * Rule 'ntp' * Rule 'dhcp4' * Rule 'printers' * Rule 'Useful Services' * Rule 'blockconfig' * Rule 'blockconfig2' * Forward 'lan' -> 'wan' * Forward 'wan' -> 'lan' * Forward 'guest' -> 'wan' * Forward 'lan' -> 'guest' * Forward 'wan' -> 'guest' * Populating IPv4 nat table * Zone 'wan' * Zone 'lan' * Zone 'guest' * Populating IPv4 mangle table * Zone 'wan' * Zone 'lan' * Zone 'guest' * Populating IPv4 raw table * Zone 'wan' * Zone 'lan' * Zone 'guest' * Populating IPv6 filter table * Zone 'wan' * Zone 'lan' * Zone 'guest' * Rule 'domain' * Rule 'ntp' * Rule 'printers' * Rule 'Useful Services' * Rule 'ipv6 dfz' * Rule 'icmpv6' * Rule 'blockconfig' * Rule 'Allow-DHCPv6' * Rule 'blockconfig2' * Forward 'lan' -> 'wan' * Forward 'wan' -> 'lan' * Forward 'guest' -> 'wan' * Forward 'lan' -> 'guest' * Forward 'wan' -> 'guest' * Populating IPv6 mangle table * Zone 'wan' * Zone 'lan' * Zone 'guest' * Populating IPv6 raw table * Zone 'wan' * Zone 'lan' * Zone 'guest' * Set tcp_ecn to on * Set tcp_syncookies to on * Set tcp_window_scaling to on Done. You should restart the router now to make these take effect. root@cerowrt:/tmp _______________________________________________ Cerowrt-devel mailing list Cerowrt-devel@lists.bufferbloat.net https://lists.bufferbloat.net/listinfo/cerowrt-devel
