cb.list, please put https://raw.github.com/dtaht/cerowrt-next/master/package/network/ipv6/6relayd/files/6relayd.init
into /etc/init.d/6relayd and see what happens. On Fri, Jan 3, 2014 at 1:15 PM, Steven Barth <[email protected]> wrote: > Hi, > > I haven't really touched 6relayd since October so not sure what is wrong > atm. > There was a problem with its init script recently due to some shell script > change in OpenWrt which I hopefully fixed yesterday (couldn't verify the > issue or fix yet though). I was also experiencing a race condition with dnsmasq, while I had it enabling ra and dhcpv6 via dnsmasq. At the moment that's turned off by default, but I did rather prefer having dns names for my ipv6 addresses... is there a good way for 6relayd and dnsmasq-dhcpv6 to co-exist? > Feel free to provide me with some debugging information of the system while > PD fails for you so I can have a look at the probable cause: > > * "ifstatus ge00" (replace ge00 with your IPv6 upstream interface) > * "ip addr list dev ge01" (replace ge01 with the interface your downstream > router is connected) > * "ps | grep 6relayd" > > Anyway I will migrate all the stuff to odhcpd soon (it's successor which > shares a good part of the codebase but is a bit better integrated with the > rest of the environment). same question re dnsmasq. > > > Regards, > > Steven > > > > On 03.01.2014 18:31, Dave Taht wrote: >> >> On Fri, Jan 3, 2014 at 11:50 AM, cb.list6 <[email protected]> wrote: >>> >>> >>> >>> On Fri, Jan 3, 2014 at 8:40 AM, Dave Taht <[email protected]> wrote: >>>> >>>> At one level I am happy to figure out this is a recently introduced bug. >>>> >>>> On the other hand I am not sure if it is 6relayd. >>>> >>>> What version of cero was working for you? >>> >>> >>> I am not entirely sure, but i think it was from September. >>> >>> CB >> >> At the moment I lack the ability to debug the breakage in ipv6 dhcp-pd >> (which is odhcpd) (I am travelling). >> >> I will on my next stop next week (tuesday) setup a dhcpv6pd server and >> see what I can see. >> >>>> On Jan 3, 2014 12:21 AM, "cb.list6" <[email protected]> wrote: >>>>> >>>>> Hi, >>>>> >>>>> I have been using CeroWRT on Comcast with a 3800 for about 6 month. >>>>> The >>>>> DHCP-PD config has always been a little unstable for me, but working. >>>>> >>>>> I recently upgraded to: >>>>> >>>>> root@cerowrt:/etc/config# uname -a >>>>> Linux cerowrt 3.10.24 #1 Tue Dec 24 10:50:15 PST 2013 mips GNU/Linux >>>>> >>>>> My WAN gets a /128, but i cannot get DHCP-PD to work to get addresses >>>>> on >>>>> the rest of my interfaces. The router does seem to have good IPv6 >>>>> access. >>>>> >>>>> >>>>> I fiddled with the 6relayd config and came up with this, but it does >>>>> not >>>>> work. Any pointers on how to get this back on track? The result of >>>>> the >>>>> below config is that the /128 from the WAN interfaces is now present on >>>>> all >>>>> the interfaces but my attached computers get no addresses. >>>>> >>>>> >>>>> config server 'default' >>>>> option rd 'server' >>>>> option dhcpv6 'server' >>>>> option management_level '1' >>>>> list network 'ge01' >>>>> list network 'gw00' >>>>> list network 'gw01' >>>>> list network 'gw10' >>>>> list network 'gw11' >>>>> list network 'se00' >>>>> list network 'sw00' >>>>> list network 'sw10' >>>>> option fallback_relay 'rd dhcpv6 ndp' >>>>> option master 'ge00' >>>>> >>>>> root@cerowrt:/etc/config# uname -a >>>>> >>>>> _______________________________________________ >>>>> Cerowrt-devel mailing list >>>>> [email protected] >>>>> https://lists.bufferbloat.net/listinfo/cerowrt-devel >>>>> >> >> > -- Dave Täht Fixing bufferbloat with cerowrt: http://www.teklibre.com/cerowrt/subscribe.html _______________________________________________ Cerowrt-devel mailing list [email protected] https://lists.bufferbloat.net/listinfo/cerowrt-devel
