This is a notification from the Help Desk.
On Jul 10, 2019 @ 07:18 am, [email protected] wrote: Send chirp_users mailing list submissions to [email protected] To subscribe or unsubscribe via the World Wide Web, visit http://intrepid.danplanet.com/mailman/listinfo/chirp_users or, via email, send a message with subject or body 'help' to [email protected] You can reach the person managing the list at [email protected] When replying, please edit your Subject line so it is more specific than "Re: Contents of chirp_users digest..." Today's Topics: 1. Error setting memory - out of supported range [Baofeng] (Adam Nielsen) 2. Re: Error setting memory - out of supported range[Baofeng] (Neil B) 3. Re: Error setting memory - out of supported range [Baofeng] (Jim Unroe) ---------------------------------------------------------------------- Message: 1 Date: Wed, 10 Jul 2019 00:42:47 +1000 From: Adam Nielsen <[email protected]> Subject: [chirp_users] Error setting memory - out of supported range [Baofeng] To: [email protected] Message-ID: <[email protected]> Content-Type: text/plain; charset=US-ASCII Hi all, I'm new to Chirp and testing it with a Baofeng F8+III (supposedly an update on the UV-5R). I have successfully downloaded all the programmed frequencies (as both BF-F8HP and UV-5R models). I named some of the channels and uploaded them, and now the radio shows the names I entered instead of the frequencies - great! However I am unable to name some of the channels as I get an error when I attempt to do so: Error setting memory: Tx freq 0.000500 is out of supported range When I programmed in this frequency, I wanted to disable transmission so that I didn't accidentally transmit by mistake. I found some instructions online that suggested setting the split such that the transmission frequency ends up in a band that the radio cannot transmit on, and this indeed works - should I try to transmit the radio beeps with an error (if beeps are enabled) and no transmission occurs. I have now successfully downloaded all my programmed channels into Chirp, including those with invalid splits, and I can upload them back to the device as well, with the invalid splits being left unchanged. However it won't let me assign names to the channels having these out of range splits because the above error comes up. Is there any way I can tell Chirp that this isn't an error, and the frequency is intentionally out of range to prevent accidental transmission, and to accept the name of the channel I am trying to set? Many thanks, Adam. ------------------------------ Message: 2 Date: Tue, 9 Jul 2019 14:59:25 +0000 From: Neil B <[email protected]> Subject: Re: [chirp_users] Error setting memory - out of supported range[Baofeng] To: Discussion of CHIRP <[email protected]> Message-ID: <cwlp123mb1827ffcb77ed1b4fe8ce5385d5...@cwlp123mb1827.gbrp123.prod.outlook.com> Content-Type: text/plain; charset="iso-8859-1" if i recall correctly, in the duplex colum, select off. that stops tx. 73's ----- Original Message ----- From: "Adam Nielsen" <[email protected]> To: <[email protected]> Sent: Tuesday, July 09, 2019 3:42 PM Subject: [chirp_users] Error setting memory - out of supported range[Baofeng] > Hi all, > > I'm new to Chirp and testing it with a Baofeng F8+III (supposedly an > update on the UV-5R). I have successfully downloaded all the > programmed frequencies (as both BF-F8HP and UV-5R models). I named > some of the channels and uploaded them, and now the radio shows the > names I entered instead of the frequencies - great! > > However I am unable to name some of the channels as I get an error > when I attempt to do so: > > Error setting memory: Tx freq 0.000500 is out of supported range > > When I programmed in this frequency, I wanted to disable transmission > so that I didn't accidentally transmit by mistake. I found some > instructions online that suggested setting the split such that the > transmission frequency ends up in a band that the radio cannot transmit > on, and this indeed works - should I try to transmit the radio beeps > with an error (if beeps are enabled) and no transmission occurs. > > I have now successfully downloaded all my programmed channels into > Chirp, including those with invalid splits, and I can upload them back > to the device as well, with the invalid splits being left unchanged. > However it won't let me assign names to the channels having these out > of range splits because the above error comes up. > > Is there any way I can tell Chirp that this isn't an error, and the > frequency is intentionally out of range to prevent accidental > transmission, and to accept the name of the channel I am trying to set? > > Many thanks, > Adam. > _______________________________________________ > chirp_users mailing list > [email protected] > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > This message was sent to m1cfk at [email protected] > To unsubscribe, send an email to > [email protected] > ------------------------------ Message: 3 Date: Tue, 9 Jul 2019 12:32:10 -0400 From: Jim Unroe <[email protected]> Subject: Re: [chirp_users] Error setting memory - out of supported range [Baofeng] To: Discussion of CHIRP <[email protected]> Message-ID: <cadno8u69swy9pvymy_gozrutmv_gu4-197njlutpplqzt88...@mail.gmail.com> Content-Type: text/plain; charset="UTF-8" > When I programmed in this frequency, I wanted to disable transmission > so that I didn't accidentally transmit by mistake. I found some > instructions online that suggested setting the split such that the > transmission frequency ends up in a band that the radio cannot transmit > on, and this indeed works - should I try to transmit the radio beeps > with an error (if beeps are enabled) and no transmission occurs. This is only valid if you are only going to manual program your radio. CHIRP checks to make sure that both the RX frequency and TX frequency are within the capability of the radio. > I have now successfully downloaded all my programmed channels into > Chirp, including those with invalid splits, and I can upload them back > to the device as well, with the invalid splits being left unchanged. > However it won't let me assign names to the channels having these out > of range splits because the above error comes up. You can't edit invalidly programmed channels. You have to "fix" the errors. > Is there any way I can tell Chirp that this isn't an error, and the > frequency is intentionally out of range to prevent accidental > transmission, and to accept the name of the channel I am trying to set? No. What you have to do is switch to the method that CHIRP uses to inhibit TX on a memory channel of these radios. That would be to set the Duplex field to "off". After doing this, you should then be able to edit the Names as desired. Jim KC9HI ------------------------------ _______________________________________________ chirp_users mailing list [email protected] http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to [email protected] End of chirp_users Digest, Vol 127, Issue 4 ******************************************* ------ This is an automated response. Your issue has been noted. We'll be in touch soon. Please reply to this email or visit the URL below with any additional details. http://SIS/portal/view-help-request/8
_______________________________________________ chirp_users mailing list [email protected] http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to [email protected] at [email protected] To unsubscribe, send an email to [email protected]
