Hm... Not for MSFC only, because comand guide recommends to configure cef... By the way, may be you try evidently configure cef on interface :)
2007/7/4, Dmitry Kiselev < [EMAIL PROTECTED]>: > > Hello! > > On Wed, Jul 04, 2007 at 05:35:31PM +0400, alexey wrote: > > > Hello! > > Dmitry, where have you find anything about egress NetFlow on 7600? :) > > I am reading config guide attentively > > > http://www.cisco.com/en/US/products/hw/routers/ps368/products_configuration_guide_chapter09186a0080699369.html#wp1078217 > > but no nothing about egress netflow! > > > But in command reference it is described > http://www.cisco.com/en/US/products/ps6922/products_command_reference_chapter09186a0080697fa4.html#wp1094522 > > > and IOS accept "ip flow egress" on interface > May be it work for MSFC switched traffic only? :) > > > > 2007/7/4, Dmitry Kiselev <[EMAIL PROTECTED] >: > > > > > > Hello! > > > > > > On my 7600 test box with RSP720 I failed to do egress netflow. > > > Here is config snapshot: > > > > > > mls flow ip interface-full > > > > > > interface GigabitEthernet1/25 > > > ip address XXX.YYY.17.2 255.255.255.252 > > > ip flow ingress > > > ip flow egress > > > ! > > > interface GigabitEthernet1/26 > > > ip address XXX.YYY.16.2 255.255.255.252 > > > ! > > > > > > > > > When I send pings between two routers connected to g1/25 and g1/26 > > > I see only g1/25 ingress flow records: > > > > > > > > > Router-XXX.YYY.17.1#ping XXX.YYY.16.1 > > > > > > Type escape sequence to abort. > > > Sending 5, 100-byte ICMP Echos to XXX.YYY.16.1, timeout is 2 seconds: > > > !!!!! > > > Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/9 ms > > > > > > > > > 7600-RSP720#sh mls netflow ip dest XXX.YYY.16.1 > > > Displaying Netflow entries in Supervisor Earl > > > DstIP SrcIP Prot:SrcPort:DstPort Src > > > i/f :AdjPtr > > > > > > > ----------------------------------------------------------------------------- > > > Pkts Bytes Age LastSeen Attributes > > > --------------------------------------------------- > > > XXX.YYY.16.1 XXX.YYY.17.1 icmp:8 :0 Gi1/25 > > > :0x0 > > > 5 500 1 14:23:37 L3 - Dynamic > > > > > > 7600-RSP-720#sh mls netflow ip sour XXX.YYY.16.1 > > > Displaying Netflow entries in Supervisor Earl > > > DstIP SrcIP Prot:SrcPort:DstPort Src > > > i/f :AdjPtr > > > > > > > ----------------------------------------------------------------------------- > > > Pkts Bytes Age LastSeen Attributes > > > --------------------------------------------------- > > > > > > 7600-RSP-720# > > > > > > > > > In my config I can't enable igress netflow on both interfaces. > > > Moreover, in production config physical interfaces need to be > > > replaced with SVIs. Is it possible to see engress hardware > > > switched traffic? > > > > > > Ahh, in slot 1 6748-GE card installed and SRB1 IOS used. > > > > > > -- > > > Dmitry Kiselev > > > _______________________________________________ > > > cisco-nsp mailing list [email protected] > > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > -- > Dmitry Kiselev > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
