Thanks Wycliffe, I already ordered for another cable and hope it will solve my problem.
Thanks for all in the List for your support and concerns. Regards, Kris Quoting Wycliffe <[EMAIL PROTECTED]>: > Normally unless routing is complete to the other side you cannot ping the > interface from the router. The CRC errors could be as a result of > > 1) Bad cable or card > 2) You have interference or an underlying carrier. > I would try and sort number 1 first > > Wycliffe > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > Sent: Friday, July 06, 2007 3:00 PM > To: [email protected] > Cc: [EMAIL PROTECTED] > Subject: Re: [c-nsp] Regarding HSSI Loop back test > > Hi Wycliffe, > > Thanks for your reply. > > I try to ping from outside and its working fine. Hope this solves my > problems. > > How come am getting lot of CRC errors as all the connectivity is fine? > > Thanks once again, > > Kris > > > ----- Original Message ----- > From: "Wycliffe" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]>; <[email protected]> > Sent: Friday, July 06, 2007 9:55 AM > Subject: RE: [c-nsp] Regarding HSSI Loop back test > > > > Hi > > Try ping the interface from outside the router. Ie on from onother > interface > > like Ethernet > > > > Wycliffe > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] On Behalf Of > > [EMAIL PROTECTED] > > Sent: Thursday, July 05, 2007 5:42 PM > > To: [email protected] > > Subject: [c-nsp] Regarding HSSI Loop back test > > > > > > > > Hi All, > > > > I am doing loopback test for HSSI in 3825 router. I have connected the > HSSI > > > > to a Comtech CDM 600 router by using HSSI to LVDS converter. > > > > Now I want to test loopback on the router to make sure HSSI is working > fine. > > > > What I did is: > > > > I have connected the router to the modem (as I told above) and I make a > > physical loop in the modem with a RF cable (connecting TX to RX). > > and I have give the following configs on the HSSI interface. > > > > #sh run interface hssi 0/1 > > ip address 83.229.2.82 255.255.255.252 > > loopback dte > > serial restart_delay 0 > > no cdp enable > > end > > > > and when I ping the interface from the console, i am not getting reply. > > Iam getting the following output when i run "sh int" command: > > > > 3825#sh int hssi 1/0 > > Hssi1/0 is up, line protocol is up > > Hardware is M1T-HSSI-B > > Internet address is 83.229.2.82/30 > > MTU 4470 bytes, BW 45045 Kbit, DLY 200 usec, > > reliability 255/255, txload 1/255, rxload 1/255 > > Encapsulation HDLC, crc 16, loopback set (dte) > > Keepalive set (10 sec) > > Restart-Delay is 0 secs > > Last input never, output 00:00:12, output hang never > > Last clearing of "show interface" counters 00:05:36 > > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > > Queueing strategy: fifo > > Output queue: 0/40 (size/max) > > 5 minute input rate 0 bits/sec, 0 packets/sec > > 5 minute output rate 0 bits/sec, 0 packets/sec > > 0 packets input, 0 bytes, 0 no buffer > > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > > 0 parity > > 18 input errors, 14 CRC, 0 frame, 3 overrun, 0 ignored, 1 abort > > 15 packets output, 680 bytes, 0 underruns > > 0 output errors, 0 applique, 22 interface resets > > 0 output buffer failures, 0 output buffers swapped out > > 46 carrier transitions LC=down CA=up TM=down LB=up TA=up LA=up > > 3825# > > > > 3825#ping 83.229.2.82 > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 83.229.2.82, timeout is 2 seconds: > > ..... > > Success rate is 0 percent (0/5) > > > > Has anyone else faced this problem before, Please share the solution > > > > Thanks in Advance > > > > Kris. > > > > ---------------------------------------------------------------------- > > This mail sent through Toaster-Horde (http://qmailtoaster.clikka.com/) > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > No virus found in this incoming message. > > Checked by AVG Free Edition. > > Version: 7.5.476 / Virus Database: 269.10.0/886 - Release Date: 7/4/2007 > > 1:40 PM > > > > > > No virus found in this outgoing message. > > Checked by AVG Free Edition. > > Version: 7.5.476 / Virus Database: 269.10.0/887 - Release Date: 7/5/2007 > > 1:55 PM > > > > > > > > > > ---------------------------------------------------------------------- > This mail sent through Toaster-Horde (http://qmailtoaster.clikka.com/) > > No virus found in this incoming message. > Checked by AVG Free Edition. > Version: 7.5.476 / Virus Database: 269.10.0/887 - Release Date: 7/5/2007 > 1:55 PM > > > No virus found in this outgoing message. > Checked by AVG Free Edition. > Version: 7.5.476 / Virus Database: 269.10.0/887 - Release Date: 7/5/2007 > 1:55 PM > > > ---------------------------------------------------------------------- This mail sent through Toaster-Horde (http://qmailtoaster.clikka.com/) _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
