Atif, Thanks for the config. The problem isnt in ISIS, its LDP. MPLS SSO and LDP graceful-restart are not supported in 12.0S. The command you have in your config "mpls ldp graceful-restart" only enables LDP helper mode, allowing the router to act as a peer to a switching-over router. Given this, RPR+ like behavior is expected. I also suspect the NSR version of ISIS allows LDP to come up faster, which is why you see better times in that scenario. MPLS SSO is only supported on the 12000 in IOS XR. Hope this helps, Ken
________________________________ From: Ken Weissner (kweissne) Sent: Tuesday, January 15, 2008 11:35 AM To: 'Atif Sid' Cc: [email protected] Subject: RE: [c-nsp] SSO with ISIS NSF (IETF vs Cisco) Can you provide the complete config and a sh hardware for P2 (offlist if necessary) and I'll see what I can tell from them. There should be no difference in switchover behavior between different RP slots. Ken ________________________________ From: Atif Sid [mailto:[EMAIL PROTECTED] Sent: Tuesday, January 15, 2008 11:26 AM To: Ken Weissner (kweissne) Cc: [email protected] Subject: Re: [c-nsp] SSO with ISIS NSF (IETF vs Cisco) another interesting this i just noticed is that Failover from RP8 to RP9 takes 30 Sec while from RP9 to RP8 is 8 secs could there be config sync issue? FAILOVER FROM RP8 TO RP9: (it reloads) P2#redundancy force-switchover Proceed with switchover? [confirm] System Bootstrap, Version 12.0(20040128:214555) [assafb-PRP1P_20040101 1.8dev(2.83)] DEVELOPMENT SOFTWARE Copyright (c) 1994-2004 by cisco Systems, Inc. DRAM DIMM Slot 1: 2048M found, Slot 2: Empty MPC7457 platform with 2097152 Kbytes of main memory Self decompressing the image : BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB BBBBBBBBBBBBBBBBBBBBBBB [OK] while RP9 to RP8: P2#redundancy force-switchover Proceed with switchover? [confirm] Switching roles - Standby to Active SEC 8:*Jan 15 11:30:47.913 EST: %MBUS-6-SWITCHOVER: Switchover initiated by active in slot 9, management request SEC 8:*Jan 15 11:30:47.953 EST: %RP-5-NEWPRIMARY: Switchover to new RP *Jan 15 11:30:47.973 EST: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up *Jan 15 11:30:47.977 EST: %LINK-5-CHANGED: Interface Ethernet1, changed state to administratively down *Jan 15 11:30:47.981 EST: %LINEPROTO-5-UPDOWN: Line protocol on Interface , changed state to up *Jan 15 11:30: 47.985 EST: %TAGCON-3-LCLTAG_ALLOC: Cannot allocate local tag *Jan 15 11:30:48.974 EST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to up *Jan 15 11:30:48.978 EST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1, changed state to down *Jan 15 11:30:48.982 EST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet2, changed state to down *Jan 15 11:30:49.610 EST: %MBUS-6-RP_STATUS: RP in Slot 8 Mode = MBUS Active and i see sessions are UP within 8 seconds. IETF were both 30 Seconds. On 1/15/08, Atif Sid <[EMAIL PROTECTED]> wrote: Ok. and this was what I exptected but testing shows that when I use IETF mode and failover it takes ~ 30 sec + to repair while in Cisco mode it can converge in 8 seconds. Here is a test: 3 routers: cisco 12410/PRP, IOS: 12.0(32)SY3 P1 --> P2 --> P3 * Pinging from p1 to p3 with timout set to 1 sec , all three routers are in NSF Cisco. * force a RP failover on P2, P1#ping Protocol [ip]: Target IP address: p3 Repeat count [5]: 10000 Datagram size [100]: Timeout in seconds [2]: 1 Extended commands [n]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 10000, 100-byte ICMP Echos to x.x.x.x, timeout is 1 seconds: Success rate is 99 percent (9992/10000), round-trip min/avg/max = 1/1/4 ms P1# On 1/15/08, Ken Weissner (kweissne) <[EMAIL PROTECTED] > wrote: Hello, I've just joined this list, so didnt have a copy of the original email to reply to, which was forwarded by a colleague. >My observation is that Cisco mode is faster then IETF, in fact IETF has as delay as being in RPR+ mode? >Is IETF a GR? vs Cisco a SSO? There should be no difference in length of outage if both these modes are functioning properly. IETF is GR mode, ie RFC3847. "Cisco" mode is a "Non-Stop Routing" mode that doesnt require interaction with the peer to recover from the processor failure due to the transfer of all state information to the standby. A "RPR+" like delay could be that the peer to the switching over router doesnt have helper capability. Thanks, Ken Weissner _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
