Hi. It sounds like your MSFC crashed. You ought to look into the crashinfo file in order to figure out why. cheers, Leonardo Gama.
________________________________ De: [EMAIL PROTECTED] em nome de Nemeth Laszlo Enviada: qui 28/2/2008 13:43 Para: [email protected] Assunto: [c-nsp] activ/standby cpu card status changed Hi! My 7604 router has 2 WS-SUP32-10GE-3B cpu card in RRP-PLUS mode. System image file is "sup-bootdisk:s3223-ipservices_wan-mz.122-18.SXF9.bin" I got this syslog messages and after it the cpu card changed the standby mode to active and active to standby. The cpu went at 100% through 15 minutes. I saw a network L2 loop, but I don't know that this L2 loop problem caused by the CPU change, or the CPU change caused by the L2 loop. I use RSTP. This router and more other 2 are members of a litle 10G ring. I can't found this error messages on cisco.com. We has a similar problem on 1 january 2008 when happend a cpu state change to (cpu was 100% like now, other time the cpu goes on 0-2%). Any idea? Thanks Laci core2#sh redundancy history | inc state Feb 28 16:13:33 *my state = ACTIVE(13) *peer state = DISABLED(1) Feb 28 16:17:12 *my state = ACTIVE(13) *peer state = UNKNOWN(0) Feb 28 16:17:21 *my state = ACTIVE(13) *peer state = STANDBY COLD(4) Feb 28 16:18:09 *my state = ACTIVE(13) *peer state = STANDBY COLD-CONFIG(5) Feb 28 16:18:19 *my state = ACTIVE(13) *peer state = STANDBY HOT(8) core2#sh redundancy switchover Switchovers this system has experienced : 1 Last switchover reason : Active crashed. Uptime since this supervisor switched to active : 8 weeks, 1 day, 18 hours, 50 minutes Total system uptime from reload : 28 weeks, 1 day, 1 hour, 29 minutes core2#sh redundancy switchover history Index Previous Current Switchover Switchover active active reason time ----- -------- ------- ---------- ---------- 1 1 2 active unit failed 22:44:19 MET Tue Jan 1 2008 *Feb 28 16:11:12 MET: %CONST_DIAG-SP-STDBY-3-HM_TEST_FAIL: Module 1 TestSPRPInbandPing consecutive failure count:7 *Feb 28 16:11:12 MET: %CONST_DIAG-SP-STDBY-6-HM_TEST_INFO: CPU util(5sec): SP=7% RP=0% Traffic=0% netint_thr_active[0], Tx_Rate[70], Rx_Rate[4946], dev=1[IPv4, fail=7] *Feb 28 16:13:12 MET: %CONST_DIAG-SP-STDBY-3-HM_TEST_FAIL: Module 1 TestSPRPInbandPing consecutive failure count:14 *Feb 28 16:13:12 MET: %CONST_DIAG-SP-STDBY-6-HM_TEST_INFO: CPU util(5sec): SP=2% RP=0% Traffic=0% netint_thr_active[0], Tx_Rate[70], Rx_Rate[8290], dev=1[IPv4, fail=14] Feb 28 16:13:33 MET: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1, changed state to down Feb 28 16:13:33 MET: %BGP-5-ADJCHANGE: neighbor xx.xxx.xxx.xxx Down Interface flap Feb 28 16:13:33 MET: %PFREDUN-SP-6-ACTIVE: Standby processor removed or reloaded, changing to Simplex mode Feb 28 16:13:33 MET: %LINK-SP-3-UPDOWN: Interface TenGigabitEthernet1/1, changed state to down Feb 28 16:13:33 MET: %LINEPROTO-SP-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1, changed state to down Feb 28 16:17:11 MET: %PFREDUN-SP-6-ACTIVE: Standby initializing for RPR-PLUS mode Feb 28 16:17:11 MET: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output. - _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
