Hi Tom
Thank you. Adapted you config but still no working. Can you please have a look on the debug output in attach. Kind Regards Pedro Wiliamo Matusse Telecomunicações de Moçambique (TDM) DSI Tel. +258 21 482820 Cell. +258 82 3080780 Fax: +258 21 487812 ----- Original Message ----- From: Tom Storey <[EMAIL PROTECTED]> Date: Tuesday, April 8, 2008 10:55 am Subject: Re: [c-nsp] SIP VoIP Config > Hi. > > If it helps, I recently configured a 1760 to connect to my ISPs > VoIP > service, and this is the config I used for my sip-ua: > > sip-ua > authentication username 08xxxxxxxx password xxxx > no remote-party-id > registrar ipv4:1.2.3.4 expires 3600 > sip-server ipv4:1.2.3.4:5060 > ! > > Initially I had issues where my calls didnt appear to be dialled > via > the VoIP provider, but with a bit of debugging from both ends we > figured out that I had to "no" the "remote-party-id" feature, > hence > you see "no remote-party-id" line in my config. > > The symptoms of my issue were I would dial the number, and it > would > sit there as if it were waiting for more characters, or it was > trying > to dial, and would eventually time out. It turns out it was > actually > dialling the number, but my VoIP provider was rejecting the call. > > You can use "debug ccsip" to see SIP messages to/from your router, > > this can help to get clues about what it going on (beware that SIP > is > quite chatty, so a lot of output can be produced at times). > > For reference, my dial-peers/voice-ports look like this: > > voice-port 3/0 > cptone AU > timeouts interdigit 4 > timeouts call-disconnect 2 > timeouts wait-release 10 > description ** FXS right ** > ! > dial-peer voice 100 pots > destination-pattern 08........ > port 3/0 > ! > dial-peer voice 200 voip > destination-pattern [0,1][2-4,7,8]........ > session protocol sipv2 > session target ipv4:1.2.3.4 > dtmf-relay sip-notify rtp-nte > signal-type ext-signal > codec g711alaw > no vad > ! > > Other than the config above, I have zero other config related to > voice > on this router - no translation rules, codec profiles, etc - the > above > two snips of config are it! > > My setup is working 100% fine, inbound and outbound. > > Hope that helps. :-) > > Tom > > On 08/04/2008, at 6:38 AM, <[EMAIL PROTECTED]> <[EMAIL PROTECTED]> wrote: > > > Hi There, > > > > > > Trying to make calls from a POTS do VOIP in SIP setup in attach, > calls> from POTS are not beeing forwarded to VoIP port. > > > > Can any one help > > > > > > > > > > > > Pedro Wiliamo Matusse > > Telecomunicações de Moçambique (TDM) > > DSI > > Tel. +258 21 482820 > > Cell. +258 82 3080780 > > Fax: +258 21 487812 > > <config HJ3825 07 04 2008 23 > > 00h.TXT>_______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
