If i remember right, "sh frame pvc xxx" will show you the "truth".
-- Tassos virendra rode // wrote on 8/4/2008 10:56 μμ: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > Hi, > > I have a class based weighted fair queue/LLQ defined and applied in a > frame-relay lab environment. > > > 1. class-map defined > 2. policy-map qos-policy > 3. applied to interface (see below) > > > interface Serial0/0/0:0 > no ip address > encapsulation frame-relay > no fair-queue > frame-relay traffic-shaping > ! > interface Serial0/0/0:0.666 point-to-point > description lab pvc > bandwidth 1024 > ip address 192.168.0.1 255.255.255.252 > frame-relay class shaper-queue-policy > frame-relay interface-dlci 666 ietf > > > map-class frame-relay shaper-queue-policy > frame-relay cir 1024000 > frame-relay be 0 > frame-relay mincir 1024000 > service-policy output queuing-policies > > > The question I have is when I look at Serial0/0/0:0 interface queue (see > below output) it shows queuing as "fifo" but looking at the show queuing > interface on the same interface (see below output) list queue strategy as > "priority". Is this correct behavior or do I need to apply "service > service-policy output" to the main interface (Serial0/0/0:0) in > order for it to be doing "class-based queueing" as opposed to "fifo"? > > > lab-gw#sh interface Serial0/0/0:0 > Serial0/0/0:0 is up, line protocol is up > Hardware is GT96K Serial > MTU 1500 bytes, BW 1024 Kbit, DLY 20000 usec, > reliability 255/255, txload 5/255, rxload 241/255 > Encapsulation FRAME-RELAY, loopback not set > Keepalive set (10 sec) > LMI enq sent 9293, LMI stat recvd 9294, LMI upd recvd 0, DTE LMI up > LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0 > LMI DLCI 1023 LMI type is CISCO frame relay DTE > FR SVC disabled, LAPF state down > Broadcast queue 0/64, broadcasts sent/dropped 9293/1, interface > broadcasts 9293 > Last input 00:00:00, output 00:00:00, output hang never > Last clearing of "show interface" counters 1d01h > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: fifo > Output queue: 0/40 (size/max) > 30 second input rate 970000 bits/sec, 85 packets/sec > 30 second output rate 21000 bits/sec, 58 packets/sec > > > lab-gw#sh queueing int Serial0/0/0:0 > Interface Serial0/0/0:0 queueing strategy: priority > > Output queue utilization (queue/count) > high/0 medium/0 normal/62520 low/0 > > > Any insight will be appreciated. > > > > regards, > /virendra > > > > -----BEGIN PGP SIGNATURE----- > Version: GnuPG v1.4.2.2 (GNU/Linux) > Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org > > iD8DBQFH+80qpbZvCIJx1bcRAklSAJ92lcGMpYAOkb/d7YYbo5F9D+3lpQCgrx+j > 8EdrhlAmpQ495KiE8wejNEc= > =zvgQ > -----END PGP SIGNATURE----- > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
