No.
On Tue, Jun 10, 2008 at 11:56:09PM -0500, Frank Bulk - iNAME wrote: > Is there any way to re-write the TTL on incoming packets so that they don't > traverse too far upstream, therefore essentially limiting this customer's > traffic to just the local LAN? > > Frank > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of root net > Sent: Tuesday, June 10, 2008 5:36 AM > To: a. rahman isnaini r.sutan > Cc: [email protected] > Subject: Re: [c-nsp] Best way to filter local traffic from Internet traffic > > I do not think shaping traffic would work as I am not trying to throttle his > traffic to everyone else but our local LAN I want to provide a circuit that > only allows local LAN traffic meaning our directly connected customers > routes only not any other routes. BGP would definitely work but I am not > sure if we can do this with this customer. Is there an alternative towards > BGP like with a ACL or route-map maybe? > > -rootnet08 > > On Tue, Jun 10, 2008 at 4:40 AM, a. rahman isnaini r.sutan < > [EMAIL PROTECTED]> wrote: > > > > > Rate-Limit/Traffic Shape Group ? > > > > > > rgsour > > a. rahman isnaini r.sutan > > > > > > root net wrote: > > > >> This customer is pretty savvy so BGP may be possible. But if not then > >> what? > >> > >> On Mon, Jun 9, 2008 at 4:26 PM, Justin M. Streiner < > >> [EMAIL PROTECTED]> > >> wrote: > >> > >> On Mon, 9 Jun 2008, root net wrote: > >>> > >>> I have a customer that wants a 100/1000 Mb/s pipe into our network for > >>> our > >>> > >>>> local customers. This customer is also a customer but he has a > >>>> dedicated > >>>> 10 > >>>> Mb/s circuit to the Internet and is maxing out on bandwidth. Wishes to > >>>> buy > >>>> the 100/1000 Mb/s pipe for our local network access only not Internet. > >>>> What > >>>> is the best way to filter this? > >>>> > >>>> If you're running BGP with this customer, or can do so, you can feed > >>> them > >>> your local and customer routes and you can have them announce their > >>> blocks > >>> to you over that pipe. Use the knobs that BGP provides, such as local > >>> preference or MED to make the prefixes sent and received over the > >>> 100/1000 > >>> Mb/s pipe preferred over their normal transit pipe. This will push > >>> traffic > >>> between your network and theirs over the higher bandwidth link, and only > >>> use > >>> the 10 Mb/s pipe if the larger one is down. > >>> > >>> That's a pretty simplistic view of it and doesn't take into account any > >>> other connectivity the customer might have. > >>> > >>> jms > >>> _______________________________________________ > >>> cisco-nsp mailing list [email protected] > >>> https://puck.nether.net/mailman/listinfo/cisco-nsp > >>> archive at http://puck.nether.net/pipermail/cisco-nsp/ > >>> > >>> _______________________________________________ > >> cisco-nsp mailing list [email protected] > >> https://puck.nether.net/mailman/listinfo/cisco-nsp > >> archive at http://puck.nether.net/pipermail/cisco-nsp/ > >> > >> > >> _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
