I'd like to see more of the OSPF config. Is this all part of area 0, or is it configured as a stubby network? If it's stubby, you may need to configure it as NSSA to get the redistributed routes back into area 0.
On Thu, Jun 12, 2008 at 2:42 PM, Paul Stewart <[EMAIL PROTECTED]> wrote: > Hi folks.. missing something obvious here.;) > > > > Cisco 6500 on one side, 2621 on other (customer prem) > > > > Relevent 6500 Config: > > > > controller T1 5/0/7 > > framing esf > > clock source internal > > linecode b8zs > > channel-group 1 timeslots 1-24 > > > > controller T1 6/0/7 > > framing esf > > clock source internal > > linecode b8zs > > channel-group 1 timeslots 1-24 > > > > interface Multilink1 > > ip address xx.xx.120.201 255.255.255.252 > > ppp multilink > > multilink-group 1 > > > > interface Serial5/0/7:1 > > no ip address > > encapsulation ppp > > ppp multilink > > multilink-group 1 > > > > interface Serial6/0/7:1 > > no ip address > > encapsulation ppp > > ppp multilink > > multilink-group 1 > > > > router ospf 1 > > log-adjacency-changes > > redistribute connected subnets > > xxxxxxxxxxxxx > > xxxxxxxxxxxxx > > > > > > 2600 Config: > > > > interface Multilink1 > > ip address xx.xx.120.202 255.255.255.252 > > ppp multilink > > ppp multilink group 1 > > > > interface Serial0/0 > > no ip address > > encapsulation ppp > > service-module t1 timeslots 1-24 > > ppp multilink > > ppp multilink group 1 > > > > interface Serial0/1 > > no ip address > > encapsulation ppp > > service-module t1 timeslots 1-24 > > ppp multilink > > ppp multilink group 1 > > > > ip route 0.0.0.0 0.0.0.0 xx.xx.120.201 > > > > > > > > >From the 6500 or the 2621 I can ping between the interfaces no problem but > can't get traffic past the 6500. It's redistributing routes via OSPF to > the > rest of our network but for some reason not the multilink IP address.. > Anything make sense about this? I can ping the local 6500 interface from > anywhere in our network but not the 2621 end (except when on the 6500). > > > > #sh ppp multilink > > > > Multilink1, bundle name is dis1-rtr-pt > > Endpoint discriminator is dis1-rtr-pt > > Bundle up for 06:32:41, total bandwidth 3072, load 1/255 > > Receive buffer limit 24000 bytes, frag timeout 1000 ms > > 0/0 fragments/bytes in reassembly list > > 0 lost fragments, 22 reordered > > 0/0 discarded fragments/bytes, 0 lost received > > 0xF19 received sequence, 0xC3E sent sequence > > Member links: 2 active, 0 inactive (max not set, min not set) > > Se0/0, since 06:32:41 > > Se0/1, since 06:32:37 > > No inactive multilink interfaces > > > > Originally we had OSPF on both sides of the link and the OSPF session would > come up no problem as "point to point" .. Confused, we moved to static > routing to try and prove this out. Is there something special you have to > do to get a multilink bundle redistributed in OSPF?? > > > > Thanks in advance, > > > > Paul Stewart > > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > -- Eric Cables _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
