It looks like you have the incorrect ip address on the remote site or the tunnel xconnect pointing to the wrong interface on the local side (FE2/0 instead of FE0/0)
Aaron On Fri, Jun 13, 2008 at 9:27 AM, Steven Pfister <[EMAIL PROTECTED]> wrote: > I've got a project I'm trying to use an l2tpv3 tunnel for. The tunnel seems > to establish just fine, but it doesn't seem to do quite what I expected it > to do. I'm trying to access vlans on a remote site that's connected via ATM. > The remote side is connected by a 3640 router, plus a 8510 switch. On the > local side, I've got another 3640, plus a 3500 switch. > > As a possible clue, doing a 'show vlans' shows many packets output, but > only a few input on the local side. On the remote side, the counts are zero > in and out. > > Here is a piece of the config on both sides. There is a vlan 77 on the > network connected to f0/0 on the remote side that I'd like to be able to > assign to the network connected to f0/0 on the local side. > > Thanks! > > --Steve > > > =========== > remote side > =========== > > l2tp-class l2-dyn > hostname ABC > password <password> > cookie size 8 > ! > pseudowire-class pw-dynamic > encapsulation l2tpv3 > protocol l2tpv3 l2-dyn > ip local interface FastEthernet0/0 > ! > interface FastEthernet0/0 > ip address 10.77.0.1 255.255.0.0 > no ip redirects > no ip proxy-arp > ip pim sparse-mode > ip route-cache flow > speed 100 > full-duplex > ! > interface FastEthernet0/0.77 > encapsulation dot1Q 77 > no snmp trap link-status > no cdp enable > xconnect 10.52.0.10 77 pw-class pw-dynamic > ! > interface ATM1/0.2 multipoint > bandwidth 2284 > ip address 10.99.60.77 255.255.255.0 > ip pim sparse-mode > no ip mroute-cache > pvc data 0/277 > protocol ip 10.99.60.1 broadcast > ubr 2284 > broadcast > encapsulation aal5snap > ! > ! > > ========== > local side > ========== > > l2tp-class l2-dyn > hostname ADM > password <password> > cookie size 8 > ! > pseudowire-class pw-dynamic > encapsulation l2tpv3 > protocol l2tpv3 l2-dyn > ip local interface FastEthernet0/0 > ! > interface FastEthernet0/0 > no ip address > duplex auto > speed auto > ! > interface FastEthernet0/0.77 > encapsulation dot1Q 77 > no snmp trap link-status > no cdp enable > xconnect 10.77.0.1 77 pw-class pw-dynamic > ! > interface FastEthernet2/0 > no ip address > no ip redirects > no ip proxy-arp > ip pim sparse-mode > duplex auto > speed auto > ! > interface FastEthernet2/0.52 > encapsulation dot1Q 52 native > ip address 10.52.0.10 255.255.0.0 > no snmp trap link-status > ! > > Steve Pfister > Technical Coordinator, > The Office of Information Technology > Dayton Public Schools > 115 S. Ludlow St. > Dayton, OH 45402 > > Office (937) 542-3149 > Cell (937) 673-6779 > Direct Connect: 137*131747*8 > Email [EMAIL PROTECTED] > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
