Like I said... I'm hoping I've just forgotten something simple and this is almost working. I've posted a piece of the config before. I'd like to post the updated version. From each side, I'm able to ping the loopback interface of the other side, and the tunnel has been up for a couple of days now.
Thanks for everyone's help! --Steve -------------- central side -------------- l2tp-class l2-dyn authentication hostname ADM password somepassword cookie size 8 ! pseudowire-class pw-dynamic encapsulation l2tpv3 protocol l2tpv3 l2-dyn ip local interface Loopback0 interface Loopback0 ip address 192.168.7.1 255.255.255.255 ! interface FastEthernet0/0 no ip address no ip redirects no ip proxy-arp ip pim sparse-mode speed 100 full-duplex ! interface FastEthernet0/0.1 encapsulation dot1Q 1 native ip address 192.168.9.1 255.255.255.0 no snmp trap link-status ! interface FastEthernet0/0.77 encapsulation dot1Q 77 no snmp trap link-status no cdp enable xconnect 192.168.7.77 77 encapsulation l2tpv3 pw-class pw-dynamic -------------- remote side -------------- l2tp-class l2-dyn authentication hostname ABC password somepassword cookie size 8 ! pseudowire-class pw-dynamic encapsulation l2tpv3 protocol l2tpv3 l2-dyn ip local interface Loopback0 ! interface Loopback0 ip address 192.168.7.77 255.255.255.255 ! interface FastEthernet0/0 no ip address no ip redirects no ip proxy-arp ip pim sparse-mode ip route-cache flow speed 100 full-duplex ! interface FastEthernet0/0.1 encapsulation dot1Q 1 native ip address 10.77.0.1 255.255.0.0 no snmp trap link-status ! interface FastEthernet0/0.77 encapsulation dot1Q 77 no snmp trap link-status no cdp enable xconnect 192.168.7.1 77 pw-class pw-dynamic Steve Pfister Technical Coordinator, The Office of Information Technology Dayton Public Schools 115 S. Ludlow St. Dayton, OH 45402 Office (937) 542-3149 Cell (937) 673-6779 Direct Connect: 137*131747*8 Email [EMAIL PROTECTED] Steve Pfister Technical Coordinator, The Office of Information Technology Dayton Public Schools 115 S. Ludlow St. Dayton, OH 45402 Office (937) 542-3149 Cell (937) 673-6779 Direct Connect: 137*131747*8 Email [EMAIL PROTECTED] >>> "John van Oppen" <[EMAIL PROTECTED]> 6/20/2008 7:48 PM >>> Yes, we use it all the time with 7204VXRs at the end sites... Works flawlessly if you configure it as a pseudowire using the "xconnect" command to tunnel an entire interface across the network. Thanks, John van Oppen Spectrum Networks LLC 206.973.8302 (Direct) 206.973.8300 (main office) -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Steven Pfister Sent: Friday, June 20, 2008 9:00 AM To: [email protected] Subject: [c-nsp] 802.1q vlans and L2TPv3 tunnels Sorry to keep sending emails on this, but this project I'm working on has been going on for a couple of months and I'd like to finish it at some point. I'm trying to gain access to vlans at a remote ATM-connected site and assign them to ports on a switch at a central location. I need to do this for about 10 remote sites, one at a time. I was told that L2TPv3 was a good thing to use for this. Now, with much help, I've got an L2TPv3 tunnel set up between the 3640 at the remote site and a 3640 plus 3550 switch at the central site. The tunnel is established, but nothing seems to go through it. Has anyone used 802.1q vlans with L2TPv3 tunnels like this? I'm sure it has to be something simple that I've forgotten about... Thanks! --Steve Steve Pfister Technical Coordinator, The Office of Information Technology Dayton Public Schools 115 S. Ludlow St. Dayton, OH 45402 Office (937) 542-3149 Cell (937) 673-6779 Direct Connect: 137*131747*8 Email [EMAIL PROTECTED] _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
