Hello, I'm having a little problem here with a new Cisco 4510R-E. It's running the following configuration:
Mod Ports Card Type Model ---+-----+--------------------------------------+------------- 5 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E 9 18 1000BaseX (GBIC) WS-X4418-GB 10 6 SFP, 10/100/1000BaseT (RJ45)V, Cisco/I WS-X4506-GB-T M MAC addresses Hw Fw Sw Status --+--------------------------------+---+------------+----------------+--------- 5 0021.d808.6a00 to 0021.d808.6a05 1.1 12.2(44r)SG 12.2(40)SG Ok 9 000c.3000.280a to 000c.3000.281b 1.1 Ok 10 001e.7ad0.f90c to 001e.7ad0.f911 1.4 Ok Mod Redundancy role Operating mode Redundancy status ----+-------------------+-------------------+---------------------------------- 5 Active Supervisor RPR Active I'm tryubg to activate the ports on the WS-X4506-GB-T, but I'm unable to get any connection. I connected the first two ports on the card to create a loopback and still the ports are shown as "not connected". I use RJ45 and have set the media-type of the ports to rj45 which is also stated in the log: 00:00:05: %C4K_REDUNDANCY-6-INIT: Initializing as ACTIVE supervisor 00:00:05: 512 MB of system memory installed. Do 'show platform hardware sdram spd' for details. 00:00:37: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan 00:00:38: %SYS-5-CONFIG_I: Configured from memory by console 00:00:38: %SYS-5-RESTART: System restarted -- Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASE-M), Version 12.2(40)SG, RELEASE SOFTWAR) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 07-Nov-07 19:52 by prod_rel_team 00:00:38: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 5 (WS-X45-SUP6-E S/N: JAE1222JOZS Hw: 1.1) is online 00:00:38: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 9 (WS-X4418-GB S/N: JAE07340WR1 Hw: 1.1) is online 00:00:38: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 10 (WS-X4506-GB-T S/N: JAE1218GSWU Hw: 1.4) is online 00:21:07: %C4K_IOSINTF-5-RJ45ACTIVE: Slot= 10 Port= 1: RJ45 connector has become active 00:45:41: %C4K_IOSINTF-5-RJ45ACTIVE: Slot= 10 Port= 2: RJ45 connector has become active Here is the port configuration: interface GigabitEthernet10/1 no switchport ip address dhcp no keepalive media-type rj45 ! interface GigabitEthernet10/2 no switchport ip address dhcp no keepalive media-type rj45 ! Is there anything I'm missing? I already changed the cabling so that's not the problem. Any ideas/suggestions welcome. Regards, Sebastian -- GPG Key-ID: 0x76B79F20 (0x1B6034F476B79F20) 'Are you Death?' ... IT'S THE SCYTHE, ISN'T IT? PEOPLE ALWAYS NOTICE THE SCYTHE. -- Terry Pratchett, The Fifth Elephant _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
