Hi Peter, most of the resources are available,,,,
6500.LAB#sh platform hardware capacity pfc L2 Forwarding Resources MAC Table usage: Module Collisions Total Used %Used 5 0 65536 24 1% VPN CAM usage: Total Used %Used 512 0 0% L3 Forwarding Resources FIB TCAM usage: Total Used %Used 72 bits (IPv4, MPLS, EoM) 524288 75 1% 144 bits (IP mcast, IPv6) 262144 5 1% detail: Protocol Used %Used IPv4 43 1% MPLS 32 1% EoM 0 0% IPv6 2 1% IPv4 mcast 3 1% IPv6 mcast 0 0% Adjacency usage: Total Used %Used 1048576 239 1% Forwarding engine load: Module pps peak-pps peak-time 5 17 589 03:42:33 UTC Wed Mar 18 2009 Netflow Resources TCAM utilization: Module Created Failed %Used 5 3 0 0% ICAM utilization: Module Created Failed %Used 5 0 0 0% Flowmasks: Mask# Type Features IPv4: 0 reserved none IPv4: 1 unused none IPv4: 2 unused none IPv4: 3 reserved none IPv6: 0 reserved none IPv6: 1 unused none IPv6: 2 unused none IPv6: 3 reserved none CPU Rate Limiters Resources Rate limiters: Total Used Reserved %Used Layer 3 9 4 1 44% Layer 2 4 2 2 50% ACL/QoS TCAM Resources Key: ACLent - ACL TCAM entries, ACLmsk - ACL TCAM masks, AND - ANDOR, QoSent - QoS TCAM entries, QOSmsk - QoS TCAM masks, OR - ORAND, Lbl-in - ingress label, Lbl-eg - egress label, LOUsrc - LOU source, LOUdst - LOU destination, ADJ - ACL adjacency Module ACLent ACLmsk QoSent QoSmsk Lbl-in Lbl-eg LOUsrc LOUdst AND OR ADJ 5 1% 1% 1% 1% 1% 1% 0% 0% 0% 0% 1% 6500.LAB# 6500.LAB# 6500.LAB#sh tcam counts Used Free Percent Used Reserved ---- ---- ------------ -------- Labels:(in) 6 4090 0 Labels:(eg) 2 4094 0 ACL_TCAM -------- Masks: 11 4085 0 72 Entries: 60 32708 0 576 QOS_TCAM -------- Masks: 7 4089 0 18 Entries: 32 32736 0 144 LOU: 0 128 0 ANDOR: 0 16 0 ORAND: 0 16 0 ADJ: 3 2045 0 6500.LAB# Regards, On Thu, Mar 26, 2009 at 2:28 PM, Peter Rathlev <pe...@rathlev.dk> wrote: > On Thu, 2009-03-26 at 10:36 +0530, Swati Sharma wrote: > > Though I have just few routes still I am getting > > > > Mar 26 04:49:06.406 UTC: %MLSCEF-SP-4-FIB_EXCEPTION: FIB TCAM > > exception for IPv4 unicast, Some routes will be software switched. > > Use "mls cef maximum-routes" to modify FIB TCAM partition. > > > > 6500.LAB#sh mls cef maximum-routes > > FIB TCAM maximum routes : > > ======================= > > Current :- > > ------- > > IPv4 + MPLS - 512k (default) > > IPv6 + IP Multicast - 256k (default) > ... > > any idea !!! > > What does "show tcam counts" and "show platform hardware capacity pfc" > say? > > Regards, > Peter > > > _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/