Slot0 we think has a defective GRP, we removed and errors are gone. I have a new GRP being shipped for tomorrow. Thanks
On Tue, Jul 21, 2009 at 5:07 PM, Aaron <[email protected]> wrote: > Looks like a fabric problem. > > > On Tue, Jul 21, 2009 at 14:34, Chris Lane <[email protected]> wrote: > >> All, >> I have a GSR 12008 with 2 GRP-B route processors. Running >> gsr-k4p-mz.120-32.S11.bin >> >> My GRP failed over about 45 minutes ago to the backup in Slot1 from Slot0. >> I keep getting this in my logs. >> SEC 0:00:00:06: %MBUS-6-FIA_CONFIG: Switch Cards 0x1F (bit mask); Primary >> Clock CSC_1 >> SEC 0:00:00:07: %FIA-3-HALT: To Fabric >> SEC 0:00:00:07: %FIA-3-PARITYERR: To Fabric parity error was detected. >> Request parity error interrupt = 0x4. >> SEC 0:00:00:07: %FIA-3-HALT: To Fabric >> SEC 0:00:00:07: %FIA-3-HALT: To Fabric >> SEC 0:00:00:07: %RP-3-FABRIC_UNI: Unicast send timed out (1) >> SEC 0:00:00:13: %RP-3-FABRIC_UNI: Unicast send timed out (1) >> SEC 0:00:00:23: %RP-3-FABRIC_UNI: Unicast send timed out (1) >> SEC 0:00:00:37: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003 >> timeout=0x6 >> -Traceback= 501F6650 505A3B90 505A3F4C 505A40D8 5059FCCC 502A02D8 502A02C4 >> SEC 0:00:00:44: %RP-3-FABRIC_UNI: Unicast send timed out (1) >> SEC 0:00:01:08: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003 >> timeout=0x6 >> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4 >> SEC 0:00:01:15: %RP-3-FABRIC_UNI: Unicast send timed out (1) >> SEC 0:00:01:39: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003 >> timeout=0x6 >> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4 >> SEC 0:00:01:56: %RP-3-FABRIC_UNI: Unicast send timed out (1) >> SEC 0:00:02:10: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003 >> timeout=0x6 >> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4 >> SEC 0:00:02:41: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003 >> timeout=0x6 >> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4 >> SEC 0:00:02:48: %RP-3-FABRIC_UNI: Unicast send timed out (1) >> SEC 0:00:03:12: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003 >> timeout=0x6 >> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4 >> SEC 0:00:03:43: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003 >> timeout=0x6 >> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4 >> SEC 0:00:03:50: %RP-3-FABRIC_UNI: Unicast send timed out (1) >> SEC 0:00:04:14: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003 >> timeout=0x6 >> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4 >> SEC 0:00:04:45: %IPC-5-REGPORTFAIL: Registering Control Port Id=0x1000003 >> timeout=0x6 >> -Traceback= 501F6650 505A3B90 505A3BD8 502A02D8 502A02C4 >> SEC 0:00:05:02: %RP-3-FABRIC_UNI: Unicast send timed out (1) >> Jul 21 12:27:01.258 EDT: %RP-3-ERROR: Timed out while initializing IPC to >> standby RP in slot 0 >> Jul 21 12:28:02.070 EDT: %MBUS-6-DEADSCDY: Standby RP in slot 0 timed out, >> reset >> >> >> Is this because SLOT0 is hung, trying to become primary again yet not >> communicating with SLOT1 the active RP? >> SLOT 0 (RP/LC 0 ): Route Processor >> MAIN: type 19, 800-2427-03 rev F0 >> Deviation: D070866 >> HW config: 0x00 SW key: 00-00-00 >> PCA: 73-2170-08 rev E0 ver 5 >> Design Release 1.5 S/N SAD0745027R >> MBUS: MBUS Agent (1) 73-2146-07 rev B0 dev 0 >> HW version 1.2 S/N CAT073504X3 >> Test hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00 >> DIAG: Test count: 0x00000000 Test results: 0x00000000 >> FRU: Linecard/Module: GRP-B= >> Route Memory: MEM-GRP-512= >> MBUS Agent Software version 2.68 (RAM) (ROM version is 3.47) >> ROM Monitor version 2.2 >> Primary clock is CSC 1 >> Board State is Route Processor Powered ( RP RDY ) ********* SHOULDN'T >> THIS SAY STANDBY (STBY RP ) >> Insertion time: 42w1d (00:56:55 ago) >> DRAM size: 536870912 bytes >> >> >> SLOT 1 (RP/LC 1 ): Route Processor >> MAIN: type 19, 800-2427-03 rev F0 >> Deviation: 0 >> HW config: 0x00 SW key: 00-00-00 >> PCA: 73-2170-08 rev E0 ver 5 >> Design Release 1.5 S/N SAD072000C3 >> MBUS: MBUS Agent (1) 73-2146-07 rev B0 dev 0 >> HW version 1.2 S/N CAT07100SFN >> Test hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00 >> DIAG: Test count: 0x00000000 Test results: 0x00000000 >> FRU: Linecard/Module: GRP-B= >> Route Memory: MEM-GRP-512= >> MBUS Agent Software version 2.68 (RAM) (ROM version is 3.47) >> ROM Monitor version 2.2 >> Primary clock is CSC 1 >> Board State is IOS Running ACTIVE (ACTV RP ) >> Insertion time: 42w1d (00:56:55 ago) >> DRAM size: 536870912 bytes >> >> >> >> Any help, suggestions greatly appreciated >> >> Chris >> >> -- >> //CL >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> > > -- //CL _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
