Open a tac case. On Mon, Aug 10, 2009 at 00:55, jack daniels <[email protected]> wrote:
> Hi All > > I'm getting below error on GSR 12416 ALARM CARD - > > IOS 12.0(32)SY6 > > > > WARNING: Unknown MBUS agent controller type, slot 24 > Contact your technical support > representative.<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Please advise > > > > sh diag 24 > > SLOT 24 (ALM 0 ): Alarm Module(16) > MAIN: type 64, 800-5570-05 rev C0 > Deviation: 0 > HW config: 0x00 SW key: 00-00-00 > PCA: 73-4266-04 rev B0 ver 3 > Design Release 1.0 S/N SAL1250CZJ9 > MBUS: Unknown (0) 00-0000-00 rev 70 dev 0 > HW version 1.2 S/N SAL1248BSQ5 > Test hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00 > DIAG: Test count: 0x00000000 Test results: 0x00000000 > FRU: Linecard/Module: GSR16-ALRM= > MBUS Agent Software version 2.68 (RAM) (ROM version is 3.66) > > > > > sh gsr > Slot 0 type = Modular SPA Interface Card > state = IOS RUN Line Card Enabled > subslot 0/0: SPA-1X10GE-L-V2 (0x50C), status is ok > subslot 0/1: Empty > subslot 0/2: Empty > subslot 0/3: Empty > Slot 5 type = Modular SPA Interface Card > state = IOS RUN Line Card Enabled > subslot 5/0: SPA-2XOC48POS/RPR (0x46F), status is ok > subslot 5/1: SPA-5X1GE-V2 (0x50A), status is ok > subslot 5/2: Empty > subslot 5/3: Empty > Slot 6 type = Modular SPA Interface Card > state = IOS RUN Line Card Enabled > subslot 6/0: SPA-4XT3/E3 (0x40B), status is ok > subslot 6/1: SPA-4XT3/E3 (0x40B), status is ok > subslot 6/2: SPA-8XOC3-POS (0x505), status is ok > subslot 6/3: SPA-8XOC3-POS (0x505), status is ok > Slot 7 type = Performance Route Processor > state = ACTV RP IOS Running ACTIVE > Slot 8 type = Performance Route Processor > state = STBY RP IOS Running STANDBY > Slot 9 type = Modular SPA Interface Card > state = IOS RUN Line Card Enabled > subslot 9/0: SPA-1X10GE-L-V2 (0x50C), status is ok > subslot 9/1: Empty > subslot 9/2: Empty > subslot 9/3: Empty > Slot 14 type = Modular SPA Interface Card > state = IOS RUN Line Card Enabled > subslot 14/0: SPA-2XOC48POS/RPR (0x46F), status is ok > subslot 14/1: SPA-5X1GE-V2 (0x50A), status is ok > subslot 14/2: Empty > subslot 14/3: Empty > Slot 15 type = Modular SPA Interface Card > state = IOS RUN Line Card Enabled > subslot 15/0: SPA-4XOC12-POS (0x507), status is ok > subslot 15/1: SPA-8XOC3-POS (0x505), status is ok > subslot 15/2: SPA-4XT3/E3 (0x40B), status is ok > subslot 15/3: Empty > Slot 16 type = Clock Scheduler Card OC192 Dual Priority > state = Card Powered > Slot 17 type = Clock Scheduler Card OC192 Dual Priority > state = Card Powered PRIMARY CLOCK > Slot 18 type = Switch Fabric Card 16XOC192 > state = Card Powered > Slot 19 type = Switch Fabric Card 16XOC192 > state = Card Powered > Slot 20 type = Switch Fabric Card 16XOC192 > state = Card Powered > Slot 24 type = Alarm Module(16) > state = Card Powered > Slot 25 type = Alarm Module(16) > state = Card Powered > Slot 27 type = Bus Board(16) > state = Card Powered > Slot 28 type = Blower Module(16) > state = Card Powered > Slot 29 type = Blower Module(16) > state = Card Powered > > > Thanks and Regards > J.Daniels > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
