Hi All, Just wondering if anybody has any ideas on what debug commands I should be using on the AS5400 to see why our fax server keeps receiving a busy signal. No changes have been done on the fax server and AS5400. We've tried rebooting both the fax server and AS5400 but no joy. We send fax requests to the fax server/gateway which is running hylafax. The server then sends the fax request to the AS5400 which is acting as a fax relay using t38. All of a sudden we are getting a "ERR Busy signal detected" in the logs on the fax server when trying to send a fax out. /var/log/messages: Oct 7 13:26:56 faxserv FaxQueuer[175]: SUBMIT JOB 9842 Oct 7 13:26:58 faxserv FaxGetty[184]: ANSWER: Can not lock modem device Oct 7 13:27:03 faxserv FaxSend[843]: MODEM VYACHESLAV FROLOV T38FAX/0.6.2 Oct 7 13:27:03 faxserv FaxSend[843]: SEND FAX: JOB 9842 DEST 0398110002 COMMID 00021663 DEVICE '/dev/ttyx1' O/G connection to [email protected] Closing connection Oct 7 13:27:09 faxserv FaxSend[843]: SEND FAILED: JOB 9842 DEST 0398110002 ERR Busy signal detected Oct 7 13:27:09 faxserv FaxQueuer[175]: NOTIFY: bin/notify "sendq/q9842" "requeued" "" "13:30" Oct 7 13:27:34 faxserv FaxGetty[184]: MODEM VYACHESLAV FROLOV T38FAX/0.6.2 hylafax log: Oct 08 00:36:06.40: [ 636]: SESSION BEGIN 00021824 61393337467 Oct 08 00:36:06.40: [ 636]: HylaFAX (tm) Version 4.1.1 Oct 08 00:36:06.40: [ 636]: SEND FAX: JOB 9857 DEST 61393337467 COMMID 00021824 DEVICE '/dev/ttyx1' Oct 08 00:36:06.40: [ 636]: MODEM set DTR OFF Oct 08 00:36:06.40: [ 636]: MODEM set baud rate: 0 baud (flow control unchanged) Oct 08 00:36:06.40: [ 636]: DELAY 75 ms Oct 08 00:36:06.48: [ 636]: MODEM set DTR ON Oct 08 00:36:06.48: [ 636]: DELAY 2600 ms Oct 08 00:36:09.08: [ 636]: MODEM set baud rate: 19200 baud, input flow RTS/CTS, output flow RTS/CTS Oct 08 00:36:09.08: [ 636]: MODEM flush i/o Oct 08 00:36:09.08: [ 636]: <-- [4:ATZ\r] Oct 08 00:36:09.10: [ 636]: --> [3:ATZ] Oct 08 00:36:09.10: [ 636]: --> [2:OK] Oct 08 00:36:09.10: [ 636]: DELAY 3000 ms Oct 08 00:36:12.10: [ 636]: <-- [5:ATE0\r] Oct 08 00:36:12.10: [ 636]: --> [4:ATE0] Oct 08 00:36:12.10: [ 636]: --> [2:OK] Oct 08 00:36:12.10: [ 636]: <-- [5:ATV1\r] Oct 08 00:36:12.10: [ 636]: --> [2:OK] Oct 08 00:36:12.10: [ 636]: <-- [5:ATQ0\r] Oct 08 00:36:12.10: [ 636]: --> [2:OK] Oct 08 00:36:12.10: [ 636]: <-- [7:ATS0=0\r] Oct 08 00:36:12.10: [ 636]: --> [2:OK] Oct 08 00:36:12.10: [ 636]: <-- [7:ATS8=2\r] Oct 08 00:36:12.10: [ 636]: --> [2:OK] Oct 08 00:36:12.10: [ 636]: <-- [8:ATS7=60\r] Oct 08 00:36:12.10: [ 636]: --> [2:OK] Oct 08 00:36:12.10: [ 636]: <-- [12:AT+FCLASS=1\r] Oct 08 00:36:12.10: [ 636]: --> [2:OK] Oct 08 00:36:12.10: [ 636]: <-- [7:ATL0M1\r] Oct 08 00:36:12.10: [ 636]: --> [2:OK] Oct 08 00:36:12.10: [ 636]: STATE CHANGE: RUNNING -> SENDING Oct 08 00:36:12.10: [ 636]: MODEM input buffering enabled Oct 08 00:36:12.10: [ 636]: <-- [12:AT+FCLASS=1\r] Oct 08 00:36:12.20: [ 636]: --> [2:OK] Oct 08 00:36:12.20: [ 636]: DIAL 61393337467 Oct 08 00:36:12.20: [ 636]: <-- [16:ATDT61393337467\r] Oct 08 00:36:12.37: [ 636]: --> [4:BUSY] Oct 08 00:36:12.37: [ 636]: SEND FAILED: JOB 9857 DEST 61393337467 ERR Busy signal detected Thanks. Andy
This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. Please notify the sender immediately by email if you have received this email by mistake and delete this email from your system. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of the organisation. Finally, the recipient should check this email and any attachments for the presence of viruses. The organisation accepts no liability for any damage caused by any virus transmitted by this email. _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
