hi Arie we made the hard reset and the logs still appear so TAC informed us that the module is faulty and we ordered a new one Thanks a lot for your help
Regards, Mohammad Khalil > Subject: RE: [c-nsp] Cisco CISCO7606-S Module > Date: Sun, 22 Aug 2010 15:37:16 +0200 > From: [email protected] > To: [email protected]; [email protected] > > Mohammad, > > This could be (after a very quick query) related to CSCef46923 "Group of > 4 ports on WS-X6516-xx modules may stop forwarding traffic" > > These are the release notes: > PROBLEM/SYMPTOMS > ================ > Under very rare conditions, a group of ports on the same port-ASIC may > experience connectivity issue. This issue can occur on any module which > uses the same port-ASIC as WS-X6516-GE-TX. > > The following syslog messages might also be seen, but is not required to > observe the issue. > > %PM_SCP-SP-6-LCP_FW_ERR_INFORM: Module 4 is experiencing the following > error: > Pinnacle #0, Frames with Bad Packet CRC Error (PI_CI_S_PKTCRC_ERR - > 0xC7) = > 110 > > > Syslog Messages update (3/14/05) > ========================================== > > Examples of Syslog message from IOS: > ______________________________________________________________ > %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 5 is experiencing the following > error: > PINNACLE Pb transient parity error detected : ports - 1 3 5 7 > > %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 5 is experiencing the following > error: > Bus Asic #1 transient Pb error. Recovered. (0x1234, 0x5678) > > > Examples of Syslog message from CatOS: > ______________________________________________________________ > > %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. > Err-disabling > port 5/5. > > %SYS-3-PKTBUFFERFAIL_PWRCYCLE:Packet buffer failure detected. Power > cycling > module 5. > > ______________________________________________________________ > > Condition > ========= > The problem usually happens to a group of ports that are connected > through the same ASIC. > > WORKAROUND > ========== > The problem will usually recover after hard-reset the module. If the > problem > keeps happening on the same module, please contact TAC. > > > > > > > So, I would suggest you contact TAC for this... > Arie > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Mohammad Khalil > Sent: Sunday, August 22, 2010 10:26 > To: [email protected] > Subject: [c-nsp] Cisco CISCO7606-S Module > > > > > We > are facing some issues with our Cisco CISCO7606-S on the > module SFM-capable 48 port 10/100/1000mb RJ45 (Model Number > WS-X6548-GE-TX) > please see the log below:Aug 21 03:53:18.275 EET: > %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 3 is experiencing the following > error: Bus Asic #0 transient Pb error. Recovered (0x0000, 0x0042) > Aug 21 03:53:31.327 EET: %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 3 is > experiencing the following error: Bus Asic #0 transient Pb error. > Recovered (0x0000, 0x0042) > Aug 21 03:53:44.579 EET: %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 3 is > experiencing the following error: Bus Asic #0 transient Pb error. > Recovered (0x0000, 0x0046) > Aug 21 03:53:57.631 EET: %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 3 is > experiencing the following error: Bus Asic #0 transient Pb error. > Recovered (0x0000, 0x0042) > Aug 21 03:54:11.392 EET: %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 3 is > experiencing the following error: Bus Asic #0 transient Pb error. > Recovered (0x0000, 0x0042) > any ideas ? > > Thanks in advance > Best Regards, > > > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
