Thanks for the tip, but I am already at the most current ROMMON revision that I am aware of:
>From my RP: Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXJ1, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2011 by Cisco Systems, Inc. Compiled Wed 22-Jun-11 18:03 by prod_rel_team ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1) >From my SP: Cisco IOS Software, s72033_sp Software (s72033_sp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXJ1, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2011 by Cisco Systems, Inc. Compiled Wed 22-Jun-11 18:47 by prod_rel_team ROM: System Bootstrap, Version 8.5(4) Also does anyone know if any issues with an older version of the Enhanced FlexWAN hardware? As from a show module on the card: Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 9 0 2 port adapter Enhanced FlexWAN WS-X6582-2PA XXXXXXXXXXX Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 9 0011.2075.d100 to 0011.2075.d13f 1.3 12.2(33)SXJ1 12.2(33)SXJ1 Ok Also from a show inventory: NAME: "9", DESCR: "WS-X6582-2PA 2 port adapter Enhanced FlexWAN Rev. 1.3" PID: WS-X6582-2PA , VID: V03, SN: XXXXXXXXXXX NAME: "module 9/0", DESCR: "Serial T3+ Port Adapter" PID: PA-2T3+ , VID: , Board revision A0, SN: XXXXXXXX NAME: "module 9/1", DESCR: "Multi-channel T1/PRI with CSU" PID: PA-8MCT1-CSU , VID: , Board revision C0, SN: XXXXXXXX I mention this, as I have a 6509 over at a clients with an Enhanced FlexWAN, but as I can see, it's a much newer version: Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 7 0 2 port adapter Enhanced FlexWAN WS-X6582-2PA YYYYYYYYYYY Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 7 0013.60cf.4a00 to 0013.60cf.4a3f 2.0 12.2(33)SXJ 12.2(33)SXJ Ok NAME: "7", DESCR: "WS-X6582-2PA 2 port adapter Enhanced FlexWAN Rev. 2.0" PID: WS-X6582-2PA , VID: V05, SN: YYYYYYYYYYY Anyway, if you or anyone has any other thoughts or suggestions, I for sure open to them... --- Howard Leadmon - [email protected] > -----Original Message----- > From: Daniel Husand [mailto:[email protected]] > Sent: Sunday, July 10, 2011 2:51 PM > To: [email protected] > Cc: Howard Leadmon > Subject: Re: [c-nsp] 6509/SUP720-3BXL with Enhanced FlexWAN issue.. Any > ideas? > > On 10/7/11 10:46 , Howard Leadmon wrote: > > > > Maybe I have I have a defective board, but you would think it would > > kick some nasty errors or something if that was the case. > > Sounds like you are hitting CSCsq77835. > > Resolved Caveats in MSFC3 ROMMON Software Release 12.2(17r)SX6 > > .The FlexWAN module configuration is corrupted during a Catalyst 6500 series > switch or Cisco 7600 series router Cisco IOS router upgrade or during bootup. > This problem is resolved in ROMMON software release 12.2(17r)SX6. > (CSCsq77835) > > -- > Daniel _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
