ASR only supports the 100m-fx GLC. The rest need to be SFP to work at all.
Jared Mauch On Nov 9, 2011, at 6:59 PM, <[email protected]> wrote: > Good evening list, > > > > Cisco has claimed that the following optics are compatible: > > > > SFP-GE-S= > > 1000BASE-SX SFP transceiver module for MMF, 850-nm wavelength, extended > operating temperature range and DOM support, dual LC/PC connector > > > > GLC-SX-MM= > > 1000BASE-SX SFP transceiver module for MMF, 850-nm wavelength, dual LC/PC > connector > > > > I have a mindbender of a problem going on in both the lab and production > currently. I have an ASR9006 running IOX 4.1.1 with: > > > > NAME: "module 0/0/CPU0", DESCR: "2-Port 10GE, 20-Port GE Line Card, Requires > XFPs and SFPs" > > PID: A9K-2T20GE-B , VID: V04, SN: FOC152786XX > > > > And in port 19 a SFP-GE-S: > > > > NAME: "module mau GigabitEthernet0/0/CPU0/19", DESCR: "1000BASE-SX SFP > (DOM), MMF, 550/220m" > > PID: SFP-GE-S , VID: V01 , SN: FNS15411KXX > > > > The interface on the asr is showing up/up. > > > > RP/0/RSP0/CPU0:oma00-dev-asr9006-1# show int gig0/0/0/19 > > Wed Nov 9 23:48:20.306 UTC > > GigabitEthernet0/0/0/19 is up, line protocol is up > > Interface state transitions: 7 > > Hardware is GigabitEthernet, address is 4055.3954.2d9d (bia > 4055.3954.2d9d) > > Internet address is 1.1.1.1/30 > > MTU 1514 bytes, BW 1000000 Kbit (Max: 1000000 Kbit) > > reliability 255/255, txload 0/255, rxload 0/255 > > Encapsulation ARPA, > > Full-duplex, 1000Mb/s, SXFD, link type is force-up > > output flow control is off, input flow control is off > > loopback not set, > > ARP type ARPA, ARP timeout 04:00:00 > > Last input never, output 00:05:04 > > Last clearing of "show interface" counters never > > 5 minute input rate 0 bits/sec, 0 packets/sec > > 5 minute output rate 0 bits/sec, 0 packets/sec > > 0 packets input, 0 bytes, 0 total input drops > > 0 drops for unrecognized upper-level protocol > > Received 0 broadcast packets, 0 multicast packets > > 0 runts, 0 giants, 0 throttles, 0 parity > > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort > > 3 packets output, 192 bytes, 0 total output drops > > Output 3 broadcast packets, 0 multicast packets > > 0 output errors, 0 underruns, 0 applique, 0 resets > > 0 output buffer failures, 0 output buffers swapped out > > 7 carrier transitions > > > > On the other end of the tested 3m multimode jumper is a catalyst 6500 > running SXJ1 with: > > > > NAME: "6", DESCR: "VS-S720-10G 5 ports Supervisor Engine 720 10GE Rev. 3.1" > > PID: VS-S720-10G , VID: V04, SN: SAL13431RXX > > > > The optic on the 6k is a GLC-SX-MM: > > > > oma00-dev-c6506-1(config-if)# do show idprom int gig6/1 > > > > Transceiver Serial EEPROM Contents: > > Common block: > > Identifier : SFP [0x03] > > Connector : LC [0x07] > > Transceiver > > Speed : Unspecified [0x00] > > Media : Unspecified [0x00] > > Technology : Unspecified [0x00] > > Link Length : [0x01] > > GE Comp Codes : Unspecified [0x00] > > SONET Comp Codes : Unspecified [0x00] > > Encoding : 8B10B [0x01] > > BR, Nominal : 13x100 MHz [0x0D] > > Length(9u) : Transceiver does not support single mode fibre, > > or the length information must be determined from > > the transceiver technology. [0x00] > > Length(50u) : 55 x 10 m [0x37] > > Length(62.5u) : 27 x 10 m [0x1B] > > Length(Copper) : Transceiver does not support copper cables, > > or the length information must be determined from > > the transceiver technology. [0x00] > > Vendor Name : CISCO-FINISAR > > Vendor OUI : 0x0 0x90 0x65 > > Vendor PN : FTLF8519P2BCL-C5 > > Vendor rev : A > > CC_BASE : 0x5F > > > > Extended ID Fields > > Options : Loss of Signal implemented TX_DISABLE is implemented > and disables the serial output > > BR, max : Unspecified 0% > > BR, min : Unspecified 0% > > Vendor SN : FNS15251SXX > > Date code : 110618 > > CC_EXT : 0xDA > > > > Vendor Specific ID Fields: > > > > 0x00: 00 00 02 D3 FB D3 38 43 25 7F 85 76 0A E3 08 51 > > 0x10: A0 2A 22 00 00 00 00 00 00 00 00 00 D6 D5 78 3A > > > > Product ID : Unspecified > > Version ID : Unspecified > > > > And interface Gig6/1 on the 6k is down/down: > > > > oma00-dev-c6506-1(config-if)#do show int gig6/1 > > GigabitEthernet6/1 is down, line protocol is down (notconnect) > > Hardware is C6k 1000Mb 802.3, address is 0019.0774.3c00 (bia > 0019.0774.3c00) > > MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, > > reliability 255/255, txload 0/255, rxload 0/255 > > Encapsulation ARPA, loopback not set > > Keepalive set (10 sec) > > Full-duplex, 1000Mb/s, media type is SX > > input flow-control is off, output flow-control is desired > > Clock mode is auto > > ARP type: ARPA, ARP Timeout 04:00:00 > > Last input never, output never, output hang never > > Last clearing of "show interface" counters never > > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > > Queueing strategy: fifo > > Output queue: 0/40 (size/max) > > 5 minute input rate 0 bits/sec, 0 packets/sec > > 5 minute output rate 0 bits/sec, 0 packets/sec > > L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes > > L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast > > L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes > > 0 packets input, 0 bytes, 0 no buffer > > Received 0 broadcasts (0 IP multicasts) > > 0 runts, 0 giants, 0 throttles > > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored > > 0 watchdog, 0 multicast, 0 pause input > > 0 input packets with dribble condition detected > > 0 packets output, 0 bytes, 0 underruns > > 0 output errors, 0 collisions, 2 interface resets > > 0 babbles, 0 late collision, 0 deferred > > 0 lost carrier, 0 no carrier, 0 PAUSE output > > 0 output buffer failures, 0 output buffers swapped out > > > > If I shutdown gig6/1 on the 6500, gig0/0/0/19 goes down on the asr9k. These > are all genuine Cisco optics and we have a TAC case pending, but as this > behavior is repeatable I thought it would be a good idea to ask for the > experience of others. > > > > There is the possibility that we are missing something obvious in the > config? We are not the most experienced group with the asr9k's or IOS-XR. > > > > RP/0/RSP0/CPU0:oma00-dev-asr9006-1#show run int gig0/0/0/19 > > Wed Nov 9 23:57:04.766 UTC > > interface GigabitEthernet0/0/0/19 > > ipv4 address 1.1.1.1 255.255.255.252 > > ! > > > > oma00-dev-c6506-1#show run int gig6/1 > > Building configuration... > > > > Current configuration : 72 bytes > > ! > > interface GigabitEthernet6/1 > > ip address 1.1.1.2 255.255.255.252 > > end > > > > The configuration is absolutely vanilla. > > > > Any help or thoughts would be greatly appreciated. > > > > Thanks! > > > > John > > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
