Did I miss the platform? It may be the service-module command.
- Jared On Apr 12, 2012, at 3:34 PM, Joseph Mays wrote: > I need to set the t1 controller for the serial interface below to be b8zs > encoding and clock source internal, but the router does not even recognize > the controller commands, and I can't find any relevant commands under the > serial interface config. > > ===== > > gw1.office#show controller serial2/0 > Interface Serial2/0 > Hardware is Quicc 68360 with Integrated FT1 CSU/DSU module > TX and RX clocks detected. > idb at 0x6416E310, driver data structure at 0x64175A34 > WIC interrupt reg = F > SCC Registers: > General [GSMR]=0x2:0x00000030, Protocol-specific [PSMR]=0x8 > Events [SCCE]=0x0000, Mask [SCCM]=0x001F, Status [SCCS]=0x0002 > Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E > Interrupt Registers: > Config [CICR]=0x00C9CF00, Pending [CIPR]=0x00000000 > Mask [CIMR]=0xC000C000, In-srv [CISR]=0x00000000 > SDMA Registers: > [SDSR]=0x00, [SDAR]=0x07A014E0, [SDCR]=0x0772 > Command register [CR]=0x600 > Port A [PADIR]=0x0000, [PAPAR]=0xFFFF > [PAODR]=0x0000, [PADAT]=0xEEFD > Port B [PBDIR]=0x0011FE, [PBPAR]=0x00000E > [PBODR]=0x000000, [PBDAT]=0x03EE5C > Port C [PCDIR]=0x000E, [PCPAR]=0x0000 > [PCSO]=0x0020, [PCDAT]=0x0FCF, [PCINT]=0x0001 > BRGC1 = 0x0000 , BRGC2 = 0x0000 > BRGC3 = 0x0000 , BRGC4 = 0x0000 > Receive Ring > rmd(3D010420): status 9000 length 2 address 7B99024 > rmd(3D010428): status 9000 length F address 7B9B724 > rmd(3D010430): status 9000 length 2 address 7B9C424 > rmd(3D010438): status 9000 length 10 address 7B9AA24 > rmd(3D010440): status 9000 length 12 address 7B996A4 > rmd(3D010448): status 9000 length 11 address 7B99D24 > rmd(3D010450): status B000 length F address 7B9A3A4 > Transmit Ring > tmd(3D010458): status 5C00 length E address 7A01894 > tmd(3D010460): status 5C00 length E address 7C14B34 > tmd(3D010468): status 5C00 length E address 7A014D4 > tmd(3D010470): status 5C00 length E address 7C161B4 > tmd(3D010478): status 5C00 length E address 7C15DF4 > tmd(3D010480): status 5C00 length E address 7A00AD4 > tmd(3D010488): status 7C00 length E address 7C14634 > > tx_limited=1(2) > > SCC GENERAL PARAMETER RAM (at 0x3D010C00) > Rx BD Base [RBASE]=0x420, Fn Code [RFCR]=0x18 > Tx BD Base [TBASE]=0x458, Fn Code [TFCR]=0x18 > Max Rx Buff Len [MRBLR]=1548 > Rx State [RSTATE]=0x18008240, BD Ptr [RBPTR]=0x440 > Tx State [TSTATE]=0x18000348, BD Ptr [TBPTR]=0x458 > > SCC HDLC PARAMETER RAM (at 0x3D010C38) > CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8 > Errors: CRC [CRCEC]=0, Aborts [ABTSC]=9, Discards [DISFC]=0 > Nonmatch Addr Cntr [NMARC]=0 > Retry Count [RETRC]=0 > Max Frame Length [MFLR]=1608 > Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=65524 > User-defined Address 0000/0000/0000/0000 > User-defined Address Mask 0x0000 > > > buffer size 1524 > QUICC SCC specific errors: > 131355 input aborts on receiving flag sequence > 0 throttles, 0 enables > 0 overruns > 0 transmitter underruns > 0 transmitter CTS losts > 20703 aborted short frames > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
