I see now. So you are testing hierarchical vpls with access pw terminated in bridge domain right? What I didn't get is from where to where are you trying to ping Is it between the access-pw and the bundle interface within the bridge domain or across the vpls?
The outputs below looked alright Just noticed the pw to test-02 is down -so that one won't ping adam -----Original Message----- From: Claes Jansson [mailto:[email protected]] Sent: Tuesday, November 27, 2012 3:50 PM To: Adam Vitkovsky Cc: [email protected] Subject: Re: [c-nsp] l2vpn me3600X to ASR9k Here is the output, currently running from XX-ro-test-01 switch, not XX-ro-test-02 as in the initial output. //Claes # # ME3600X # XX-ro-test-01#sh mpls l2transport vc detail Local interface: Vl444 up, line protocol up, Eth VLAN 444 up Interworking type is Ethernet Destination address: 1.1.1.2, VC ID: 444, VC status: up Output interface: Te0/1, imposed label stack {16000 16015} Preferred path: not configured Default path: active Next hop: 1.1.2.2 Create time: 04:11:03, last status change time: 04:10:57 Last label FSM state change time: 04:10:57 Last peer autosense occurred at: 04:10:57 Signaling protocol: LDP, peer 1.1.1.2:0 up Targeted Hello: 1.1.1.221(LDP Id) -> 1.1.1.2, LDP is UP Status TLV support (local/remote) : enabled/supported LDP route watch : enabled Label/status state machine : established, LruRru Last local dataplane status rcvd: No fault Last BFD dataplane status rcvd: Not sent Last BFD peer monitor status rcvd: No fault Last local AC circuit status rcvd: No fault Last local AC circuit status sent: No fault Last local PW i/f circ status rcvd: No fault Last local LDP TLV status sent: No fault Last remote LDP TLV status rcvd: No fault Last remote LDP ADJ status rcvd: No fault MPLS VC labels: local 26, remote 16015 Group ID: local 0, remote 4 MTU: local 1500, remote 1500 Remote interface description: Access PW Sequencing: receive disabled, send disabled Control Word: Off (configured: autosense) Dataplane: SSM segment/switch IDs: 8219/4121 (used), PWID: 8 VC statistics: transit packet totals: receive 2293, send 19143 transit byte totals: receive 203612, send 3547582 transit packet drops: receive 0, seq error 0, send # # ASR # RP/0/RSP0/CPU0:XX-ro-core-02#sh l2vpn bridge-domain bd-name vlan10 detail Tue Nov 27 15:42:32.432 CET Legend: pp = Partially Programmed. Bridge group: canaldigital, bridge-domain: vlan10, id: 4, state: up, ShgId: 0, MSTi: 0 Coupled state: disabled MAC learning: enabled MAC withdraw: enabled MAC withdraw for Access PW: enabled MAC withdraw sent on bridge port down: disabled Flooding: Broadcast & Multicast: enabled Unknown unicast: enabled MAC aging time: 300 s, Type: inactivity MAC limit: 4000, Action: none, Notification: syslog MAC limit reached: no MAC port down flush: enabled MAC Secure: disabled, Logging: disabled Split Horizon Group: none Dynamic ARP Inspection: disabled, Logging: disabled IP Source Guard: disabled, Logging: disabled DHCPv4 snooping: disabled IGMP Snooping profile: none Bridge MTU: 1500 MIB cvplsConfigIndex: 5 Filter MAC addresses: Create time: 23/11/2012 14:38:00 (4d01h ago) No status change since creation ACs: 1 (1 up), VFIs: 1, PWs: 3 (2 up), PBBs: 0 (0 up) List of ACs: AC: Bundle-Ether1.10, state is up Type VLAN; Num Ranges: 1 VLAN ranges: [10, 10] MTU 1500; XC ID 0xa0000009; interworking none MAC learning: enabled Flooding: Broadcast & Multicast: enabled Unknown unicast: enabled MAC aging time: 300 s, Type: inactivity MAC limit: 4000, Action: none, Notification: syslog MAC limit reached: no MAC port down flush: enabled MAC Secure: disabled, Logging: disabled Split Horizon Group: none Dynamic ARP Inspection: disabled, Logging: disabled IP Source Guard: disabled, Logging: disabled DHCPv4 snooping: disabled IGMP Snooping profile: none Storm Control: disabled Static MAC addresses: Statistics: packets: received 41606, sent 13575 bytes: received 2989424, sent 3747002 Storm control drop counters: packets: broadcast 0, multicast 0, unknown unicast 0 bytes: broadcast 0, multicast 0, unknown unicast 0 Dynamic ARP inspection drop counters: packets: 0, bytes: 0 IP source guard drop counters: packets: 0, bytes: 0 List of Access PWs: PW: neighbor 1.1.1.221, PW ID 444, state is up ( established ) PW class not set, XC ID 0xc000000b Encapsulation MPLS, protocol LDP Source address 1.1.1.2 PW type Ethernet, control word disabled, interworking none PW backup disable delay 0 sec Sequencing not set PW Status TLV in use MPLS Local Remote ------------ ------------------------------ --------------------------- Label 16015 26 Group ID 0x4 0x0 Interface Access PW unknown MTU 1500 1500 Control word disabled disabled PW type Ethernet Ethernet VCCV CV type 0x2 0x12 (LSP ping verification) (LSP ping verification) VCCV CC type 0x6 0x2 (router alert label) (router alert label) (TTL expiry) ------------ ------------------------------ --------------------------- Incoming Status (PW Status TLV): Status code: 0x0 (Up) in Notification message MIB cpwVcIndex: 3221225483 Create time: 27/11/2012 10:04:53 (05:38:15 ago) Last time status changed: 27/11/2012 11:35:37 (04:07:32 ago) MAC withdraw message: send 0 receive 0 Static MAC addresses: Statistics: packets: received 4597, sent 2474 bytes: received 2069874, sent 164908 Storm control drop counters: packets: broadcast 0, multicast 0, unknown unicast 0 bytes: broadcast 0, multicast 0, unknown unicast 0 MAC learning: enabled Flooding: Broadcast & Multicast: enabled Unknown unicast: enabled MAC aging time: 300 s, Type: inactivity MAC limit: 4000, Action: none, Notification: syslog MAC limit reached: no MAC port down flush: enabled MAC Secure: disabled, Logging: disabled Split Horizon Group: none DHCPv4 snooping: disabled IGMP Snooping profile: none Storm Control: disabled PW: neighbor 1.1.1.222, PW ID 444, state is down ( local ready ) (Segment-down) PW class not set, XC ID 0xc000000a Encapsulation MPLS, protocol LDP Source address 1.1.1.2 PW type Ethernet, control word disabled, interworking none PW backup disable delay 0 sec Sequencing not set PW Status TLV in use MPLS Local Remote ------------ ------------------------------ --------------------------- Label 16017 40 Group ID 0x4 0x0 Interface Access PW unknown MTU 1500 1500 Control word disabled disabled PW type Ethernet Ethernet VCCV CV type 0x2 0x12 (LSP ping verification) (LSP ping verification) VCCV CC type 0x6 0x2 (router alert label) (router alert label) (TTL expiry) ------------ ------------------------------ --------------------------- Incoming Status (PW Status TLV): Status code: 0x6 (AC Down) in Notification message MIB cpwVcIndex: 3221225482 Create time: 27/11/2012 09:17:30 (06:25:39 ago) Last time status changed: 27/11/2012 10:01:38 (05:41:30 ago) MAC withdraw message: send 0 receive 0 Static MAC addresses: MAC learning: enabled Flooding: Broadcast & Multicast: enabled Unknown unicast: enabled MAC aging time: 300 s, Type: inactivity MAC limit: 4000, Action: none, Notification: syslog MAC limit reached: no MAC port down flush: enabled MAC Secure: disabled, Logging: disabled Split Horizon Group: none DHCPv4 snooping: disabled IGMP Snooping profile: none Storm Control: disabled List of VFIs: VFI cd (up) PW: neighbor 1.1.1.1, PW ID 10, state is up ( established ) PW class not set, XC ID 0xc0000008 Encapsulation MPLS, protocol LDP Source address 1.1.1.2 PW type Ethernet, control word disabled, interworking none PW backup disable delay 0 sec Sequencing not set PW Status TLV in use MPLS Local Remote ------------ ------------------------------ ------------------------- Label 16014 16023 Group ID 0x4 0x8 Interface cd cd MTU 1500 1500 Control word disabled disabled PW type Ethernet Ethernet VCCV CV type 0x2 0x2 (LSP ping verification) (LSP ping verification) VCCV CC type 0x6 0x6 (router alert label) (router alert label) (TTL expiry) (TTL expiry) ------------ ------------------------------ ------------------------- Incoming Status (PW Status TLV): Status code: 0x0 (Up) in Notification message MIB cpwVcIndex: 3221225480 Create time: 26/11/2012 00:03:57 (1d15h ago) Last time status changed: 26/11/2012 13:14:17 (1d02h ago) MAC withdraw message: send 15 receive 5 Static MAC addresses: Statistics: packets: received 5441, sent 22808 bytes: received 972971, sent 3534592 DHCPv4 snooping: disabled IGMP Snooping profile: none VFI Statistics: drops: illegal VLAN 0, illegal length 0 On 2012-11-27 15:30, Adam Vitkovsky wrote: > What does the "sh l2vpn bridge-domain det" or sh l2vpn bridge-domain > int det says? > > adam > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Claes Jansson > Sent: Tuesday, November 27, 2012 1:50 PM > To: [email protected] > Subject: [c-nsp] l2vpn me3600X to ASR9k > > Hi! > > I have stumpled across a wierd problem, and would like some input on > where to dig for the answer :-) > > > My setup looks like this... All links are routed directly on the > interface (/31), no MPLS over SVI. > > XX-ro-test-02 (ME3600X) <--> XX-ro-test-01 (ME3600X) <--> > XX-ro-core-01 (ASR9K) <--> XX-ro-core-02 (ASR9K) <--> XX-ro-core-10 > (ME3600X) > > > The problem is that when i do a xconnect from ME3600 (tried from > test-02 and test-01) to core-02 it fail's. But when connecting them to > core-01 or core-10 it works. > > I also have connected the l2vpn bridge-domain "vlan10" between core-01 > and core-02 by VFI/VPLS. > Both the ASR9K and ME3600 shows the xconnect as status "UP". > > > # Software and hardware > ASR9K, running 4.2.1 no SMU's > RSP440, LineCard, MOD80 (AIP), MPAs 1x20GE, 1x4TE ME3600X, running > 15.2(4)S1 (AdvIP) > > # All devices can reach eachother through lo0 # OSPF, MP-BGP and LDP > running. > # l3 vpn works, even from XX-ro-core-02 > > # > ---------------------------------------------------------------------- > ------ > -------- > > # > # XX-ro-core-01 > # lo0 = 1.1.1.1 > l2vpn > bridge group cd > bridge-domain vlan10 > neighbor 1.1.1.222 pw-id 555 > ! > vfi cd > neighbor 1.1.1.2 pw-id 10 > ! > > # > # XX-ro-core-02 > # lo0 = 1.1.1.2 > l2vpn > bridge group cd > bridge-domain vlan10 > interface Bundle-Ether1.10 > ! > neighbor 1.1.1.222 pw-id 444 > ! > vfi cd > neighbor 1.1.1.1 pw-id 10 > ! > # Looped to bundle-ethernet1.10 > RP/0/RSP0/CPU0:XX-ro-core-02#sh run int bundle-ether101.10 Tue Nov 27 > 10:16:44.368 CET interface Bundle-Ether101.10 > vrf cd > ipv4 mtu 1500 > ipv4 helper-address vrf mgmt 10.0.10.12 > ipv4 address 10.10.95.1 255.255.255.128 > encapsulation dot1q 10 > ! > # Looped to bundle-ethernet101.10 > RP/0/RSP0/CPU0:XX-ro-core-02#sh run int bundle-ether1.10 Tue Nov 27 > 10:16:49.155 CET interface Bundle-Ether1.10 l2transport > encapsulation dot1q 10 exact > rewrite ingress tag pop 1 symmetric ! > > > # XX-ro-test-02 > #lo0 1.1.1.222 > > interface GigabitEthernet0/11 > switchport trunk allowed vlan none > switchport mode trunk > service instance 444 ethernet > description test > encapsulation dot1q 444 > rewrite ingress tag pop 1 symmetric > bridge-domain 444 > ! > ## TEST SETUP, FAILING! > interface Vlan444 > no ip address > xconnect 1.1.1.2 444 encapsulation mpls ! > > XX-ro-test-01#sh mac address-table vlan 444 .... > 444 0025.9065.1de8 DYNAMIC Gi0/11+Efp444 > 444 0025.906e.73c5 DYNAMIC Gi0/11+Efp444 > 444 6c9c.ed3f.a842 DYNAMIC 1.137.102.28, 258821064 # This > ALWAYS show as a seemingly random ip and pw-id... > > Although ping fails, I can see packets (ping) from the ASR to the > end-host (tcpdump). > And ARP records shows up as they should in both the ASR and the end host. > > But! > Every 4-minutes, 7 (Seven), ICMP ping replies goes through... > 64 bytes from 10.10.95.1: icmp_req=6144 ttl=255 time=0.811 ms > 64 bytes from 10.10.95.1: icmp_req=6145 ttl=255 time=0.974 ms > 64 bytes from 10.10.95.1: icmp_req=6146 ttl=255 time=0.841 ms > 64 bytes from 10.10.95.1: icmp_req=6147 ttl=255 time=0.890 ms > 64 bytes from 10.10.95.1: icmp_req=6148 ttl=255 time=0.835 ms > 64 bytes from 10.10.95.1: icmp_req=6149 ttl=255 time=0.871 ms > 64 bytes from 10.10.95.1: icmp_req=6150 ttl=255 time=0.825 ms ! > 64 bytes from 10.10.95.1: icmp_req=6400 ttl=255 time=0.914 ms > 64 bytes from 10.10.95.1: icmp_req=6401 ttl=255 time=0.846 ms > 64 bytes from 10.10.95.1: icmp_req=6402 ttl=255 time=0.866 ms > 64 bytes from 10.10.95.1: icmp_req=6403 ttl=255 time=2.12 ms > 64 bytes from 10.10.95.1: icmp_req=6404 ttl=255 time=0.837 ms > 64 bytes from 10.10.95.1: icmp_req=6405 ttl=255 time=0.903 ms > 64 bytes from 10.10.95.1: icmp_req=6406 ttl=255 time=0.801 ms > > Wierd or what..? > > > # TEST SETUP, WORKING! > > interface Vlan444 > no ip address > xconnect 1.1.1.1 555 encapsulation mpls ! > XX-ro-test-01#sh mac address-table vlan 444 > 444 0025.9065.1de8 DYNAMIC Gi0/11+Efp444 > 444 0025.906e.73c5 DYNAMIC Gi0/11+Efp444 > 444 6c9c.ed3f.a842 DYNAMIC 1.1.1.1, 555 # This sometimes > show as a seemingly random ip and pw-id. But can be reset by removing > int vlan444 and adding it again with the exact same config. Although > even with a random ip/pw-id traffic flows... > > Tnx! > > //Claes > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
