You can find help on the following links: http://docs.fortinet.com/fgt/handbook/40mr3/fortigate-ipsec-40-mr3.pdf
http://docs.fortinet.com/fgt/handbook/40mr2/fortigate-ipsec-40-mr2.pdf http://kb.fortinet.com/kb/microsites/search.do?cmd=displayKC&docType=kc&externalId=FD32864&sliceId=1&docTypeID=DT_KCARTICLE_1_1&dialogID=40856996&stateId=0%200%2040858146 Regards Alberto -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Joe Freeman Sent: December-11-12 8:37 AM To: Cisco-nsp Subject: [c-nsp] Site to site vpn Cisco Router to Fortinet Greetings- I am trying to get an ipsec tunnel up between a cisco router and a Fortinet 200B for a customer. I've got IKE phase 1 completing, but phase 2 won't complete because the router's proposal isn't matching the firewall's- 2012-12-11 09:29:50 ike 1:SJCGW:324472:144706408: specified selectors mismatch 2012-12-11 09:29:50 ike 1:SJCGW:324472:144706408: peer: type=7/7, ports=0/0, protocol=0/0 2012-12-11 09:29:50 ike 1:SJCGW:324472:144706408: local=0.0.0.0-255.255.255.255, remote=0.0.0.0-255.255.255.255 2012-12-11 09:29:50 ike 1:SJCGW:324472:144706408: mine: type=7/7, ports=0/0, protocol=0/0 2012-12-11 09:29:50 ike 1:SJCGW:324472:144706408: local=XX.XX.XX.0-XX.XX.XX.255, remote=10.52.132.0-10.52.133.255 2012-12-11 09:29:50 ike 1:SJCGW:324472:144706408: specified selectors mismatch I've been trying to figure out how to set the router to match, but since I'm using a tunnel interface in ipsec mode, I haven't seen anything that works yet. Here's the router config: crypto isakmp policy 1 encr 3des authentication pre-share group 2 lifetime 8600 ! crypto isakmp policy 5 encr aes authentication pre-share group 2 lifetime 8600 ! crypto isakmp policy 10 encr aes hash sha256 authentication pre-share group 2 lifetime 8600 crypto isakmp key XXXXXXXXX address <firewall_ip_addr> no-xauth crypto isakmp keepalive 10 ! ! crypto ipsec transform-set CPS_TSET esp-3des esp-sha-hmac ! crypto ipsec profile CPS set transform-set CPS_TSET interface Tunnel186 description IPsec interface to Firewall ip address <XXXXXXX> tunnel source Loopback0 tunnel mode ipsec ipv4 tunnel destination <firewall_ip_addr> tunnel protection ipsec profile CPS I'm thinking I need an ACL and some way to apply it to the crypto profile, but I haven't found anything like that for a tunnel interface. Any thoughts or suggestions are appreciated! Thanks- Joe _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
