For the archives -

When using EIGRP inside a VRF, you need to specify an autonomous system number 
in the EIGRP config for that VRF:

!
router eigrp 21949
 vrf management
  address-family ipv4
   default-information allowed out
   autonomous-system 21949
   interface Loopback21949
   !
   interface TenGigE0/2/0/9.4003
   !
  !
 !
!

Works like a charm.

On 2013-05-31, at 5:56 PM, Jason Lixfeld <[email protected]> wrote:

> Hi,
> 
> It's been years since I've configured EIGRP and I remember it being quite 
> simple, so I'm probably missing something silly, right?
> 
> I've done some debugs and XE sends hellos to XR, but the XR debug doesn't 
> show the inbound hellos and doesn't seem to be sending any out itself.  It 
> doesn't seem to be doing much of anything, as a matter of fact.
> 
> I've tried this on 4.2.3 and 4.3.1, no dice on either.
> 
> Anyone have any ideas?
> 
> RP/0/RSP0/CPU0:bfr01.77MowatAv01.YYZ#sh debug
> Fri May 31 17:38:12.073 EDT
> 
> ####  debug flags set from tty 'vty0'  ####
> eigrp fsm flag is ON
> eigrp vrfs flag is ON
> eigrp packets flag is ON with value '0x0,none'
> eigrp internal flag is ON
> eigrp neighbor flag is ON with value 0
> eigrp transmit flag is ON with value 0
> 
> 
> RP/0/RSP0/CPU0:bfr01.77MowatAv01.YYZ#
> 
> XR 4.2.1
> 
> !
> interface Loopback21949
> description Loopback for Management
> vrf management
> ipv4 address 10.219.49.1 255.255.255.255
> ipv6 address 2607:f0c8:0:1::1/128
> !
> interface TenGigE0/2/0/9.4003
> description 4500 Management
> mtu 1500
> vrf management
> ipv4 address 10.219.45.241 255.255.255.240
> encapsulation dot1q 4003
> !
> router eigrp 21949
> vrf management
>  address-family ipv4
>   default-information allowed out
>   interface Loopback21949
>   !
>   interface TenGigE0/2/0/9.4003
>   !
>  !
> !
> !
> 
> RP/0/RSP0/CPU0:bfr01.77MowatAv01.YYZ#sh eigrp vrf management topology 
> Fri May 31 17:34:20.083 EDT
> 
> % IPv4-EIGRP: No routes found
> 
> RP/0/RSP0/CPU0:bfr01.77MowatAv01.YYZ#sh eigrp vrf management neighbors 
> Fri May 31 17:34:29.539 EDT
> 
> % IPv4-EIGRP: No neighbors found for vrf management
> 
> RP/0/RSP0/CPU0:bfr01.77MowatAv01.YYZ#sh eigrp vrf management interfaces 
> Fri May 31 17:30:51.410 EDT
> 
> IPv4-EIGRP interfaces for AS(0)
> 
>                        Xmit Queue   Mean   Pacing Time   Multicast    Pending
> Interface        Peers  Un/Reliable  SRTT   Un/Reliable   Flow Timer   Routes
> Lo21949            0        0/0         0     640/640          0           0
> Te0/2/0/9.4003     0        0/0         0     640/640          0           0
> RP/0/RSP0/CPU0:bfr01.77MowatAv01.YYZ#
> 
> XE 3.2.0 XO (4500 SUP7L-E)
> 
> !
> interface Loopback21949
> ip address 10.219.45.1 255.255.255.255
> !
> interface Vlan4003
> description Resi 4500 Management VLAN
> ip address 10.219.45.242 255.255.255.240
> logging event link-status
> !
> router eigrp 21949
> network 10.219.45.0 0.0.0.255
> passive-interface Loopback21949
> !
> 
> rgw01.lab#sh ip eigrp topology 
> EIGRP-IPv4 Topology Table for AS(21949)/ID(10.219.45.1)
> Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
>       r - reply Status, s - sia Status 
> 
> P 10.219.45.1/32, 1 successors, FD is 128256
>        via Connected, Loopback21949
> P 10.219.45.240/28, 1 successors, FD is 2816
>        via Connected, Vlan4003
> 
> rgw01.lab#sh ip eigrp neighbors 
> EIGRP-IPv4 Neighbors for AS(21949)
> rgw01.lab#sh ip eigrp interfaces 
> EIGRP-IPv4 Interfaces for AS(21949)
>                        Xmit Queue   Mean   Pacing Time   Multicast    Pending
> Interface        Peers  Un/Reliable  SRTT   Un/Reliable   Flow Timer   Routes
> Vl4003             0        0/0         0       0/1            0           0
> rgw01.lab#               
> 
> 
> RP/0/RSP0/CPU0:bfr01.77MowatAv01.YYZ#ping vrf management 10.219.45.242
> Fri May 31 17:35:18.255 EDT
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 10.219.45.242, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
> RP/0/RSP0/CPU0:bfr01.77MowatAv01.YYZ#
> 
> 
> rgw01.lab#ping 10.219.45.241
> 
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 10.219.45.241, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
> rgw01.lab#
> 
> 
> _______________________________________________
> cisco-nsp mailing list  [email protected]
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/


_______________________________________________
cisco-nsp mailing list  [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/

Reply via email to