I have a c7204VXR NPE-G1 1GB RAM 6 GigE (3 on the NP, 1 on the I/O, and 2 PA-GE). Passing about 150Gbps of traffic. It's taking a full eBGP feed (470k routes), and connected to a peering fabric (30k routes so far).
When I turned up the peering fabric, I spiked the cpu for about 5 minutes and it settled down nicely. CPU utilization now is 25% max on core1, 20% on core2. I need to enable iBGP on it. It's peer will be another c7204 (NPE-G1, 1GB, 3 GigE) with a full BGP feed (450k routes). I have about 250Mbps backhaul link between the routers. Right now, the memory utilization is about 40% on both routers which leads me to believe I could easily hold 2 full tables on both routers. I may end up with a 3rd iBGP peer with another full feed too, so if this ends up being linear, I'm figuring I can do simple math on the RAM utilization. Can I get some confirmation from anyone who either has 2 BGP feeds on their 7200VXR or has iBGP with full eBGP tables on both routers, and tell me that I'm not going to melt down the two routers when I turn up iBGP? My gut says I'll be just fine. thanks Eric Stats below core1#sh ip bgp sum BGP router identifier 67.xxx.xxx.100, local AS number 2xxxx BGP table version is 17685401, main routing table version 17685401 447841 network entries using 52397397 bytes of memory 504542 path entries using 26236184 bytes of memory 80432/75327 BGP path/bestpath attribute entries using 9973568 bytes of memory 66127 BGP AS-PATH entries using 1820802 bytes of memory 4894 BGP community entries using 290336 bytes of memory 1 BGP extended community entries using 24 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 90718311total bytes of memory (about 100 Mbytes) 1258 received paths for inbound soft reconfiguration BGP activity 3808783/3360941 prefixes, 4450994/3946452 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 64.211.193.209 4 3549 4587262 41246 17685384 0 0 1w5d 446643 66.xxx.xxx.10 4 4xxx6 41288 3175949 17685384 0 0 4w0d 1 66.xxx.xxx.82 4 3xxx1 378453 371596 17685401 0 0 3w1d 1 66.209.124.90 4 5xxx7 41003 41292 17685401 0 0 4w0d 0 206.223.143.252 4 19996 9026 1035 17685384 0 0 17:04:00 28207 206.223.143.253 4 19996 9015 1035 17685384 0 0 17:04:00 28417 core1#show memory Head Total(b) Used(b) Free(b) Lowest(b) Largest(b) Processor 63ADD410 928131852 362097708 566034144 564822488 374483724 (about 350Mbytes) I/O C000000 67108864 12448104 54660760 54490928 54262236 Transient 7B000000 16777216 17436 16759780 16367684 16752164 utilization is 39% core2#sh ip bgp sum BGP router identifier 66.xxx.xxx.252, local AS number 2xxxx BGP table version is 788940103, main routing table version 788940103 447789 network entries using 52391313 bytes of memory 447789 path entries using 23285028 bytes of memory 114097/114095 BGP path/bestpath attribute entries using 14148028 bytes of memory 114070 BGP AS-PATH entries using 3217852 bytes of memory 5 BGP community entries using 120 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP using 93042341total bytes of memory (about 100Mbytes RAM) 17 received paths for inbound soft reconfiguration BGP activity 11660283/11212493 prefixes, 13183481/12735692 paths, scan interval 60 secs Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 64.94.111.13 4 10912 733746106 1128729 788940103 0 0 25w5d 447757 core2#sh mem Head Total(b) Used(b) Free(b) Lowest(b) Largest(b) Processor 63AE23D0 928111436 369270884 558840552 557289036 374463308 (350Mbytes used) I/O C000000 67108864 8678976 58429888 58311184 58154780 Transient 7B000000 16777216 14944 16762272 16525620 16762272 utilization is 40% _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
