You do have ip multicast-routing distributed configured, right? From memory this command cannot be configured on IP Base.
On Tue, Aug 13, 2013 at 4:38 PM, selamat pagi <[email protected]> wrote: > Intressting link, helps to understand PIM Stub :-) > > Started off with IPBase on the CE and* ip pim passive on* the SVI. > For testing purpose I upgraded the CE to IPservices. --> still the same > behaviour :-( > > BTW: I use static rp and pim sparse. > > many thanks, keti > > > > > On Mon, Aug 12, 2013 at 11:03 PM, Christopher Pole <[email protected]> > wrote: > > > Are you running IPBase on your CE by any chance? PIM sparse-dense mode > need > > at least IPServices on a 3x50 if I remember correctly (the switch will > take > > the commands but you'll see no multicast traffic). There is a work around > > using PIM stub and manually announcing a bsr & rp candidate ( > > https://supportforums.cisco.com/thread/2153703) which I had to use > > recently. > > > > Chris > > [email protected] > > > > > > On Tue, Aug 13, 2013 at 12:12 AM, selamat pagi <[email protected]> > wrote: > > > > > Here is part of my LAB-setup: > > > > > > PE (RP lo 0) > > > vrf RED (ip igmp join-group 239.5.5.5) > > > ¦ > > > ¦ PIM > > > ¦ > > > CE (SVI / PIM SM (ip igmp join-group 239.6.6.6) > > > ¦ > > > ¦ IGMP > > > ¦ > > > Receiver (ip igmp join-group 239.8.8.8) > > > > > > -------------------------------------------- > > > PE5 6500 151-1.SY1 > > > CE 3750X 150-2.SE2 > > > Receiver 3750X 150-2.SE2 > > > -------------------------------------------- > > > The issue is: > > > Receiver can reach 239.6.6.6 and 239.5.5.5 > > > PE or CE cannot reach 239.8.8.8 > > > > > > Changing CE and receiver from 3750X to 6500, MC-ping works from all 3 > > > devices to any MC-group. > > > > > > PE: > > > (*, 239.8.8.8), 02:43:40/00:02:45, RP 5.5.5.5, flags: S > > > Incoming interface: Null, RPF nbr 0.0.0.0 > > > Outgoing interface list: > > > TenGigabitEthernet2/5, Forward/Sparse, 02:39:09/00:02:45 > > > > > > (5.5.5.5, 239.8.8.8), 00:14:15/00:02:57, flags: T > > > Incoming interface: Loopback0, RPF nbr 0.0.0.0 > > > Outgoing interface list: > > > TenGigabitEthernet2/5, Forward/Sparse, 00:14:15/00:02:45 > > > > > > > > > Debug on CE does not show any output. (deb ip icmp) > > > > > > Is there any 3750X specific command I need to enable ? > > > > > > Any idea or troubleshooting advice is greatly appreciated. > > > > > > many thanks, keti > > > _______________________________________________ > > > cisco-nsp mailing list [email protected] > > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
