yep, *ip multicast-routing* distributed is configured cheers, keti
On Tue, Aug 13, 2013 at 11:35 AM, Joshua Morgan <[email protected]>wrote: > You do have ip multicast-routing distributed configured, right? From > memory this command cannot be configured on IP Base. > > > On Tue, Aug 13, 2013 at 4:38 PM, selamat pagi <[email protected]> wrote: > >> Intressting link, helps to understand PIM Stub :-) >> >> Started off with IPBase on the CE and* ip pim passive on* the SVI. >> >> For testing purpose I upgraded the CE to IPservices. --> still the same >> behaviour :-( >> >> BTW: I use static rp and pim sparse. >> >> many thanks, keti >> >> >> >> >> On Mon, Aug 12, 2013 at 11:03 PM, Christopher Pole <[email protected]> >> wrote: >> >> > Are you running IPBase on your CE by any chance? PIM sparse-dense mode >> need >> > at least IPServices on a 3x50 if I remember correctly (the switch will >> take >> > the commands but you'll see no multicast traffic). There is a work >> around >> > using PIM stub and manually announcing a bsr & rp candidate ( >> > https://supportforums.cisco.com/thread/2153703) which I had to use >> > recently. >> > >> > Chris >> > [email protected] >> > >> > >> > On Tue, Aug 13, 2013 at 12:12 AM, selamat pagi <[email protected]> >> wrote: >> > >> > > Here is part of my LAB-setup: >> > > >> > > PE (RP lo 0) >> > > vrf RED (ip igmp join-group 239.5.5.5) >> > > ¦ >> > > ¦ PIM >> > > ¦ >> > > CE (SVI / PIM SM (ip igmp join-group 239.6.6.6) >> > > ¦ >> > > ¦ IGMP >> > > ¦ >> > > Receiver (ip igmp join-group 239.8.8.8) >> > > >> > > -------------------------------------------- >> > > PE5 6500 151-1.SY1 >> > > CE 3750X 150-2.SE2 >> > > Receiver 3750X 150-2.SE2 >> > > -------------------------------------------- >> > > The issue is: >> > > Receiver can reach 239.6.6.6 and 239.5.5.5 >> > > PE or CE cannot reach 239.8.8.8 >> > > >> > > Changing CE and receiver from 3750X to 6500, MC-ping works from all 3 >> > > devices to any MC-group. >> > > >> > > PE: >> > > (*, 239.8.8.8), 02:43:40/00:02:45, RP 5.5.5.5, flags: S >> > > Incoming interface: Null, RPF nbr 0.0.0.0 >> > > Outgoing interface list: >> > > TenGigabitEthernet2/5, Forward/Sparse, 02:39:09/00:02:45 >> > > >> > > (5.5.5.5, 239.8.8.8), 00:14:15/00:02:57, flags: T >> > > Incoming interface: Loopback0, RPF nbr 0.0.0.0 >> > > Outgoing interface list: >> > > TenGigabitEthernet2/5, Forward/Sparse, 00:14:15/00:02:45 >> > > >> > > >> > > Debug on CE does not show any output. (deb ip icmp) >> > > >> > > Is there any 3750X specific command I need to enable ? >> > > >> > > Any idea or troubleshooting advice is greatly appreciated. >> > > >> > > many thanks, keti >> > > _______________________________________________ >> > > cisco-nsp mailing list [email protected] >> > > https://puck.nether.net/mailman/listinfo/cisco-nsp >> > > archive at http://puck.nether.net/pipermail/cisco-nsp/ >> > > >> > _______________________________________________ >> > cisco-nsp mailing list [email protected] >> > https://puck.nether.net/mailman/listinfo/cisco-nsp >> > archive at http://puck.nether.net/pipermail/cisco-nsp/ >> > >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
