Hi,
On Tue, 13 Aug 2013, selamat pagi wrote:
yep, *ip multicast-routing* distributed is configured
you also have the correct sdm template setup on the switch ?
I assume you could not configure multicast routing otherwise.
Greetings
Christian
cheers, keti
On Tue, Aug 13, 2013 at 11:35 AM, Joshua Morgan <[email protected]>wrote:
You do have ip multicast-routing distributed configured, right? From
memory this command cannot be configured on IP Base.
On Tue, Aug 13, 2013 at 4:38 PM, selamat pagi <[email protected]> wrote:
Intressting link, helps to understand PIM Stub :-)
Started off with IPBase on the CE and* ip pim passive on* the SVI.
For testing purpose I upgraded the CE to IPservices. --> still the same
behaviour :-(
BTW: I use static rp and pim sparse.
many thanks, keti
On Mon, Aug 12, 2013 at 11:03 PM, Christopher Pole <[email protected]>
wrote:
Are you running IPBase on your CE by any chance? PIM sparse-dense mode
need
at least IPServices on a 3x50 if I remember correctly (the switch will
take
the commands but you'll see no multicast traffic). There is a work
around
using PIM stub and manually announcing a bsr & rp candidate (
https://supportforums.cisco.com/thread/2153703) which I had to use
recently.
Chris
[email protected]
On Tue, Aug 13, 2013 at 12:12 AM, selamat pagi <[email protected]>
wrote:
Here is part of my LAB-setup:
PE (RP lo 0)
vrf RED (ip igmp join-group 239.5.5.5)
¦
¦ PIM
¦
CE (SVI / PIM SM (ip igmp join-group 239.6.6.6)
¦
¦ IGMP
¦
Receiver (ip igmp join-group 239.8.8.8)
--------------------------------------------
PE5 6500 151-1.SY1
CE 3750X 150-2.SE2
Receiver 3750X 150-2.SE2
--------------------------------------------
The issue is:
Receiver can reach 239.6.6.6 and 239.5.5.5
PE or CE cannot reach 239.8.8.8
Changing CE and receiver from 3750X to 6500, MC-ping works from all 3
devices to any MC-group.
PE:
(*, 239.8.8.8), 02:43:40/00:02:45, RP 5.5.5.5, flags: S
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
TenGigabitEthernet2/5, Forward/Sparse, 02:39:09/00:02:45
(5.5.5.5, 239.8.8.8), 00:14:15/00:02:57, flags: T
Incoming interface: Loopback0, RPF nbr 0.0.0.0
Outgoing interface list:
TenGigabitEthernet2/5, Forward/Sparse, 00:14:15/00:02:45
Debug on CE does not show any output. (deb ip icmp)
Is there any 3750X specific command I need to enable ?
Any idea or troubleshooting advice is greatly appreciated.
many thanks, keti
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
--
Christian Kratzer CK Software GmbH
Email: [email protected] Wildberger Weg 24/2
Phone: +49 7032 893 997 - 0 D-71126 Gaeufelden
Fax: +49 7032 893 997 - 9 HRB 245288, Amtsgericht Stuttgart
Web: http://www.cksoft.de/ Geschaeftsfuehrer: Christian Kratzer
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
