Hi, We are doing routed SVI connected to a vfi between two ME3600 and a Cat6500 (SUP2T). Like this on one of the ME3600:
l2 vfi VPLS-120 manual vpn id 120 neighbor 172.16.250.11 encapsulation mpls neighbor 172.16.250.13 encapsulation mpls interface Vlan120 ip vrf forwarding VRF-A ip address 10.1.1.1 255.255.255.0 xconnect vfi VPLS-120 However, I read your question as you have p2p xconnects in the bridge domain, in addition to the vfi? That I have not implemented or tested. Also, I think the SVI has to be UP for the VC to be brought up. Regards, /Ulrik Ivers -----Original Message----- From: cisco-nsp [mailto:[email protected]] On Behalf Of Adam Vitkovsky Sent: den 20 januari 2014 16:29 To: [email protected] Subject: [c-nsp] BVI on ME3600? Hi folks, Is there a support for bvi or routed interface in bridge-domain or vfi on me3600. I'd like to terminate couple of p2p xconnects in a common bridge-domain/vfi along with a vlan interface with vrf designation and ip address and I can't get it working. l2 vfi corporate-inet manual vpn id 2 bridge-domain 4001 neighbor 10.105.1.5 1412171450 encapsulation mpls ! ! interface Vlan4001 mtu 9000 vrf forwarding inet ip address 192.168.50.4 255.255.255.0 xconnect vfi corporate-inet sh l2 vfi VFI name: corporate-inet, state: down, type: multipoint, signaling: LDP VPN ID: 2 Bridge-Domain 4001 attachment circuits: Vlan4001 Pseudo-port interface: pseudowire100009 Interface Peer Address VC ID S pseudowire100010 10.105.1.5 1412171450 Y sh mpls l2 vc 1412171450 det Local interface: VFI corporate-inet vfi down Interworking type is Ethernet Destination address: 10.105.1.5, VC ID: 1412171450, VC status: down Last error: Local access circuit is not ready for label advertise Output interface: none, imposed label stack {} Preferred path: not configured Default path: no route No adjacency Create time: 00:06:34, last status change time: 4w3d Last label FSM state change time: 00:06:34 Signaling protocol: LDP, peer 10.105.1.5:0 up Targeted Hello: 10.105.1.6(LDP Id) -> 10.105.1.5, LDP is UP Graceful restart: configured and enabled Non stop routing: not configured and not enabled Status TLV support (local/remote) : enabled/supported LDP route watch : enabled Label/status state machine : remote ready, LndRru Last local dataplane status rcvd: No fault Last BFD dataplane status rcvd: Not sent Last BFD peer monitor status rcvd: No fault Last local AC circuit status rcvd: DOWN(hard-down, not-ready) Last local AC circuit status sent: No fault Last local PW i/f circ status rcvd: No fault Last local LDP TLV status sent: No status Last remote LDP TLV status rcvd: No fault Last remote LDP ADJ status rcvd: No fault MPLS VC labels: local unassigned, remote 24 Group ID: local unknown, remote 0 MTU: local unknown, remote 9000 Remote interface description: [inet] backhaul for corporate inet common subnet Sequencing: receive disabled, send disabled Control Word: Off (configured: autosense) Dataplane: SSM segment/switch IDs: 0/0 (used), PWID: 7 VC statistics: transit packet totals: receive 0, send 0 transit byte totals: receive 0, send 0 transit packet drops: receive 0, seq error 0, send 0 thanks adam _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
