Also in Cisco Section remove PW-Class configuration and try this on Attachment circuit:
Xconnect x.x.x.x y encapsulation mpls -----Original Message----- From: Alireza Soltanian [mailto:[email protected]] Sent: Sunday, April 24, 2016 3:41 PM To: 'Mohammad Khalil' <[email protected]>; '[email protected]' <[email protected]> Subject: RE: [c-nsp] Cisco Juniper Xconnect Hi I cannot read JunOS configuration part properly, But it seems you did not disable Control-word on Juniper side. Did you check this? -----Original Message----- From: cisco-nsp [mailto:[email protected]] On Behalf Of Mohammad Khalil Sent: Sunday, April 24, 2016 3:22 PM To: [email protected] Subject: [c-nsp] Cisco Juniper Xconnect Hi all Am trying to simulate xconnect between Cisco and Juniper using GNS3 will it work in the first manner on GNS3? if so , please check my conf below R2 - R1 - J1 - R3 R2 interface FastEthernet0/0 no ip address speed 100 full-duplex interface FastEthernet0/0.23 encapsulation dot1Q 23 ip address 192.168.23.2 255.255.255.0 R3 interface FastEthernet0/0 no ip address speed 100 full-duplex interface FastEthernet0/0.23 encapsulation dot1Q 23 ip address 192.168.23.3 255.255.255.0 R1 router ospf 1 router-id 1.1.1.1 network 1.1.1.1 0.0.0.0 area 0 network 192.168.101.1 0.0.0.0 area 0 interface FastEthernet1/0 ip address 192.168.101.1 255.255.255.0 speed 100 duplex full mpls ip mpls mtu 1514 interface FastEthernet1/1 no ip address speed 100 duplex full interface FastEthernet1/1.23 encapsulation dot1Q 23 xconnect 10.10.10.10 23 encapsulation mpls pw-class MSSK pseudowire-class MSSK encapsulation mpls interworking vlan no control-word J1 set version 12.1R1.9 set system root-authentication encrypted-password cisco123 set system syslog user * any emergency set system syslog file messages any notice set system syslog file messages authorization info set system syslog file interactive-commands interactive-commands any set interfaces em0 mtu 1514 set interfaces em0 unit 0 family inet address 192.168.101.10/24 set interfaces em0 unit 0 family mpls mtu 1500 set interfaces em1 vlan-tagging set interfaces em1 unit 23 encapsulation vlan-ccc set interfaces em1 unit 23 vlan-id 23 set interfaces em1 unit 23 family ccc set interfaces lo0 unit 0 family inet address 10.10.10.10/32 set protocols mpls interface em0.0 set protocols mpls interface lo0.0 set protocols ospf area 0.0.0.0 interface em0.0 set protocols ospf area 0.0.0.0 interface lo0.0 set protocols ldp interface em0.0 set protocols ldp interface lo0.0 set protocols l2circuit neighbor 1.1.1.1 interface em1.23 virtual-circuit-id 23 set protocols l2circuit neighbor 1.1.1.1 interface em1.23 mtu 1500 set protocols l2circuit neighbor 1.1.1.1 interface em1.23 encapsulation-type ethernet-vlan set protocols l2circuit neighbor 1.1.1.1 interface em1.23 ignore-encapsulation-mismatch set protocols l2circuit neighbor 1.1.1.1 interface em1.23 ignore-mtu-mismatch R1#sh xconnect all Legend: XC ST=Xconnect State S1=Segment1 State S2=Segment2 State UP=Up DN=Down AD=Admin Down IA=Inactive SB=Standby HS=Hot Standby RV=Recovering NH=No Hardware XC ST Segment 1 S1 Segment 2 S2 ------+---------------------------------+--+-------------------------------- -+-- UP pri ac Fa1/1.23:23(Eth VLAN) UP mpls 10.10.10.10:23 UP R1#sh mpls l2transport vc 23 detail Local interface: Fa1/1.23 up, line protocol up, Eth VLAN 23 up Destination address: 10.10.10.10, VC ID: 23, VC status: up Output interface: Fa1/0, imposed label stack {299776} Preferred path: not configured Default path: active Next hop: 192.168.101.10 Create time: 00:09:08, last status change time: 00:09:08 Last label FSM state change time: 00:09:08 Signaling protocol: LDP, peer 10.10.10.10:0 up Targeted Hello: 1.1.1.1(LDP Id) -> 10.10.10.10, LDP is UP Status TLV support (local/remote) : enabled/not supported LDP route watch : enabled Label/status state machine : established, LruRru Last local dataplane status rcvd: No fault Last BFD dataplane status rcvd: Not sent Last BFD peer monitor status rcvd: No fault Last local AC circuit status rcvd: No fault Last local AC circuit status sent: No fault Last local PW i/f circ status rcvd: No fault Last local LDP TLV status sent: No fault Last remote LDP TLV status rcvd: Not sent Last remote LDP ADJ status rcvd: No fault MPLS VC labels: local 19, remote 299776 Group ID: local 0, remote 0 MTU: local 1500, remote 1500 Remote interface description: Remote VLAN id: 23 Sequencing: receive disabled, send disabled Control Word: Off Dataplane: SSM segment/switch IDs: 4112/4109 (used), PWID: 1 VC statistics: transit packet totals: receive 0, send 5 transit byte totals: receive 0, send 410 transit packet drops: receive 0, seq error 0, send 0 R2#ping 192.168.23.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.23.3, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) Thanks BR, Mohammad _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
