What if...just what if, it's alternating between 3 and 4 digits every time you unplug it? Try unplugging it and re-plugging it into the same router to validate this crazy idea.
On Sun Nov 16 2014 at 7:21:11 PM Jason Aarons (AM) < [email protected]> wrote: > If you move circuit to another router and it works, then its hard to > blame the carrier! > > CAS stinks. > > > Sent from my Verizon Wireless 4G LTE Smartphone > > > -------- Original message -------- > From: Ryan Huff > Date:11/16/2014 15:45 (GMT-05:00) > To: "Jason Aarons (AM)" , [email protected] > Subject: RE: [cisco-voip] E1 CAS card in Mexico not getting enough digits > > Ahh, missed the part about CAS, sorry. > > So is the provider doing something on their side with the MAC of the E1 on > your side? If the provider is sending 3 digits (regardless if it works on > the other router) then it should be their issue. > > You have the plan and type set according to what the provider expects? > > Are you getting 3 digits for the calling or called party? > > ------------------------------ > From: [email protected] > To: [email protected]; [email protected] > Subject: RE: [cisco-voip] E1 CAS card in Mexico not getting enough digits > Date: Sun, 16 Nov 2014 19:56:50 +0000 > > CAS no q931 > > > > Debug shows on bad router we receive 3 digits from provider, move circuit > to another router we receive 4 digits from provider. > > > > *From:* Ryan Huff [mailto:[email protected]] > *Sent:* Sunday, November 16, 2014 8:52 AM > *To:* Jason Aarons (AM); [email protected] > *Subject:* RE: [cisco-voip] E1 CAS card in Mexico not getting enough > digits > > > > > > So on router B, do the following and then place an inbound call from a > known number: > > hostname# conf t > hostname (config)# logging console > hostname (config)# exit > hostname# term mon > hostname# debug isdn q931 > > What do you see for "Calling Party Number i =", "Plan:" and "Type:"? The > "plan" and "type" fields should be located below the "calling > party number" field. Once you've determined that you really are receiving > 4 digits from the telco on that circuit the next step is to figure out what > in the router config is stripping the digit. If you find that you are not > receiving 4 digits from the telco, you can either work with the telco to > fix it on the PRI or if the missing digit is a constant, you can add it > with an inbound voice translation rule. > > Look at your inbound dial peers; do you have any voice translation rules > that are doing any digit stripping? Are the inbound voice translations > using different regex than on the router that is working and if so, what is > different? > > Thanks, > > Ryan Huff > CCIE Collaboration (Written), CCNP Voice, CCNA Voice > CCNA Route/Switch, CCNA Wireless, UCCX Specialist > ------------------------------ > > From: [email protected] > To: [email protected] > Date: Sun, 16 Nov 2014 08:18:22 +0000 > Subject: [cisco-voip] E1 CAS card in Mexico not getting enough digits > > I have a problem with a E1 CAS site in Mexico. I have two routers. Router > B is problem. > > > > In router A I see 4 digits come in on DTMF. > > In router B I see 3 digits come in on DTMF. We are missing 1 digit. > > > > I swap the circuit and works fine in router A. Same IOS both routers. > > > > Controller e1 0/0/0 > > Framing NO-CRC4 > > dso-group 0 timeslots 1-10 type r2-digital dtmf dnis > > cas-custom 0 > > Country telmex > > Seizure-ackt-time 2 > > > > > > > > > > > _______________________________________________ cisco-voip mailing list > [email protected] > https://puck.nether.net/mailman/listinfo/cisco-voip > > > > itevomcid > _______________________________________________ > cisco-voip mailing list > [email protected] > https://puck.nether.net/mailman/listinfo/cisco-voip >
_______________________________________________ cisco-voip mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-voip
