That was definitely one issue. I was pretty sure I entered that command manually, but apparently not. So that's why the last one did not come up.
Still very weird. I had always assumed that the router asked for the configuration for enabled ports only. Sent from my iPhone On Oct 2, 2017, at 6:24 PM, Evgeny Izetov <[email protected]<mailto:[email protected]>> wrote: I wonder if you only had enough DSPs for those 2 and 1/3 PRIs. On Oct 2, 2017 4:02 PM, "Lelio Fulgenzi" <[email protected]<mailto:[email protected]>> wrote: Well, apparently, CUCM enabling of ports overrides the router configuration. I did have all four ports configured. After deleting those two ports, the running now matches the startup. This is very weird. Is there a configuration command that says only download configuration for the ports I’ve enabled? --- Lelio Fulgenzi, B.A. Senior Analyst, Network Infrastructure Computing and Communications Services (CCS) University of Guelph 519-824-4120 Ext 56354<tel:(519)%20824-4120> [email protected]<mailto:[email protected]> www.uoguelph.ca/ccs<http://www.uoguelph.ca/ccs> Room 037, Animal Science and Nutrition Building Guelph, Ontario, N1G 2W1 From: cisco-voip [mailto:[email protected]<mailto:[email protected]>] On Behalf Of Lelio Fulgenzi Sent: Monday, October 02, 2017 2:29 PM To: voyp list, cisco-voip ([email protected]<mailto:[email protected]>) Subject: [cisco-voip] T1 PRI configuration on 2921 not matching startup config OK – Having a weird issue. I was pretty sure that the router config took precedence over CUCM (with respect to enabling ports). I’ve got four of the four ports configured on CUCM. So not sure why three are being configured on the router. Very strange! My startup looks something like this: controller T1 0/0/0 cablelength long 0db pri-group timeslots 1-24 service mgcp ! controller T1 0/0/1 cablelength long 0db pri-group timeslots 1-24 service mgcp ! controller T1 0/0/2 shutdown cablelength long 0db ! controller T1 0/0/3 shutdown cablelength long 0db ! <snip> ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-dms100 isdn incoming-voice voice isdn bind-l3 ccm-manager no cdp enable ! interface Serial0/0/1:23 no ip address encapsulation hdlc isdn switch-type primary-dms100 isdn incoming-voice voice isdn bind-l3 ccm-manager isdn bchan-number-order ascending no cdp enable <snip> voice-port 0/0/0:23 echo-cancel coverage 64 ! voice-port 0/0/1:23 ! But after a reload, my running config looks something like this: controller T1 0/0/0 cablelength long 0db pri-group timeslots 1-24 service mgcp ! controller T1 0/0/1 cablelength long 0db pri-group timeslots 1-24 service mgcp ! controller T1 0/0/2 cablelength long 0db pri-group timeslots 1-8,24 service mgcp ! controller T1 0/0/3 cablelength long 0db ! <snip> interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-dms100 isdn incoming-voice voice isdn bind-l3 ccm-manager no cdp enable ! interface Serial0/0/1:23 no ip address encapsulation hdlc isdn switch-type primary-dms100 isdn protocol-emulate network isdn incoming-voice voice isdn bind-l3 ccm-manager no cdp enable ! interface Serial0/0/2:23 no ip address encapsulation hdlc isdn switch-type primary-dms100 isdn incoming-voice voice isdn bind-l3 ccm-manager no cdp enable ! <snip> ! voice-port 0/0/0:23 echo-cancel coverage 64 ! voice-port 0/0/1:23 echo-cancel coverage 64 ! voice-port 0/0/2:23 echo-cancel coverage 64 --- Lelio Fulgenzi, B.A. Senior Analyst, Network Infrastructure Computing and Communications Services (CCS) University of Guelph 519-824-4120 Ext 56354<tel:(519)%20824-4120> [email protected]<mailto:[email protected]> www.uoguelph.ca/ccs<http://www.uoguelph.ca/ccs> Room 037, Animal Science and Nutrition Building Guelph, Ontario, N1G 2W1 _______________________________________________ cisco-voip mailing list [email protected]<mailto:[email protected]> https://puck.nether.net/mailman/listinfo/cisco-voip
_______________________________________________ cisco-voip mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-voip
